Keithley S540 Скачать руководство пользователя страница 44

Страница: 44 / 80

Section 3: Equipment startup

S540 Power Semiconductor Test System Administrative Guide

3-2

S540-924-01 Rev. D / January 2019

Figure 35: S540 power distribution unit (PDU) circuit breaker

Press the power/standby button on the computer and monitor.

Set the power button on the front door of the system cabinet to the ON position.

Figure 36: S540 power ON switch

System startup

To start up the system:

Make sure that the power switch on the power distribution unit (PDU) is set to ON.

Set the power button on the front door of the system cabinet to the ON position.

If the computer has not started to boot, open the front cabinet door and press the power/standby

switch on the host computer.

Wait for all of the instruments to power up.

Log onto your computer.

Содержание S540

















































































Результаты поиска

Содержание S540

Отзывы:

Похожие инструкции для S540

Бренды по названию

Популярные бренды

Keithley S540, Административное руководство

Результаты поиска

Содержание S540

Отзывы:

Похожие инструкции для S540

Бренды по названию

Популярные бренды