background image

DMM6500 6½-Digit Multimeter with Scanning Calibration and Adjustment Manual 

Section 3: Adjustment 

 

DMM6500-905-01 Rev. E June 2021 

3-5 

 

Initial instrument setup 

Before adjusting calibration, make sure that the instrument is set up: 

 

For remote operation and TSP commands. 

 

To the correct date and time. 

You must also unlock calibration. 

 

Select the correct terminals 

On the DMM6500, you must adjust calibration from both the front and rear terminals. You can verify 

calibration on either the front or rear terminals. To set the instrument to the rear-panel terminals, 

press the 

TERMINALS 

switch on the front panel of the instrument. 

 

Select the TSP command set 

Calibration adjustment must be performed by remote control using LAN, USB, or optional GPIB 

interfaces. No front-panel calibration commands are available. 

Calibration is only available using TSP commands. See the instructions below to change the 

command set. 

To set the command set from the front panel: 

1.  Press the 

MENU

 key. 

2.  Under System, select 

Settings

3.  For Command Set, select 

TSP

4.  You are prompted to reboot. 

 

To verify which command set is selected from a remote interface: 

Send the command: 

*LANG? 

To change to the TSP command set from a remote interface: 

Send the command: 

*LANG TSP 

Reboot the instrument. 

 

Содержание DMM6500




























































































































Отзывы: