manualshive.com logo in svg
background image

555518_A

p9.

M3i INDOOR GROUP CYCLE

OPERATION

4.    Attach the brackets on the end of the flywheel guard, 

refer to Figure 8. Use the M6 x 45 hex head screw and 
nut (supplied). Hand tighten the screw and nut.

5.    Tighten the brackets to the base frame with the two 

6mm Allen screws and washers removed in step 1. Do 
not fully tighten the bolts.

6.    Check to ensure that there is enough clearance between 

the flywheel and the flywheel guard.

7.    Tighten the bolts to secure the flywheel guard.

1.  Unwrap the pedals and the thread locking compound.
2.  Apply LPS#3 to the left bottom bracket bearing.
3.  Apply LPS #3 to the clip-in portion of the pedals.
4.  Clean the threads of the pedals with a clean cloth.
5.  Apply thread locking compound to the pedal threads.
6.  Use a 15mm open-end wrench and install the pedals: 

Left Pedal

 - Thread the left pedal (marked L) into the left side 

of the left crank arm by turning it counter-clockwise,  
refer to Figure 9.   

Right Pedal 

- Thread the right pedal (marked R) into the right 

side of the right crank arm by turning it clockwise, 
refer to Figure 10.

7.  Tighten the pedals with a torque wrench, 15mm crowfoot, 

and 4-inch extension. Torque the pedals to  
45 Nm (35 ft-lbs).

INSTALLING THE PEDALS

WARNING: Failing to install the pedals with a thread locking compound, or crossing the threads will 
damage them, and could result in serious injury to the user.

Figure 8. Align, Attach, and Tighten Flywheel Guard Brackets

Figure 10. Installing the Right Pedal, Turn Clockwise

Figure 9. Installing the Left Pedal, Turn Counter-Clockwise

NOTE: A torque wrench with a 15mm crowfoot and 4-inch extension, and a15mm open-end wrench are required to install the 

Содержание M3i lite





















Отзывы: