manualshive.com logo in svg
background image

555518_A

p3.

M3i INDOOR GROUP CYCLE

OPERATION

1. 

Read these instructions.

2. 

Keep these instructions.

3. 

Heed all warnings.

4. 

Follow all instructions.

5. 

Only use replacement parts recommended 
by Keiser Corporation.

6. 

Replace defective components immediately 
and/or keep the equipment out of use until 
repaired.

7. 

Routinely check and pay special attention to 
components most susceptible to wear.

8. 

Maximum weight of the rider shall not 
exceed 300lbs (136kg).

9. 

The cycle is NOT designed with a freewheel, 
but a fixed gear system. When the flywheel is 
in motion, the pedals will also be in motion.

10.  Never remove your feet from the pedals while the 

flywheel is in motion as serious user injury may occur.

11.  Always secure the pedal clip strap by placing your foot 

on the pedal and in the toe cage. Locate the strap and 
pull up on it to tighten. It should be snug but not too 
tight to cause discomfort.

12.  The resistance shifter allows you to safely slow or stop 

the motion of the flywheel. Move the resistance shifter 
away from you to increase the gear and slow the motion 
of the flywheel.

13.  This cycle is intended for use in training areas of 

organizations such as sport associations, educational 
establishments, hotels, clubs and studios, where 
access and control is specifically regulated by the 
owner (person who has the legal responsibility).

14.  Keep children and pets clear from the unit at all times, 

especially while in use.

15.  The cycle should be positioned on a stable, level, 

horizontal surface.

16.  There should be a clearance of no less than 24-inches 

(0.6 m) of free area on all sides of the cycle. When 
cycles are positioned adjacent to each other the free 
area may be shared.

17.  Movements such as pedaling at high speeds or 

pedaling while standing are considered advanced 
techniques, and should only be performed when the 
rider has reached an  advanced level.

18.  Ensure that all adjustment handles that could interfere 

with the user’s movement are not left projecting as to 
come in contact with the rider during operation.

19.  Before dismounting, push the resistance lever to the 

most forward position to bring both the flywheel and 
pedals to a complete stop.

WARNING: This symbol appearing throughout this manual means PAY ATTENTION! BE ALERT! When 
you see this warning symbol, your safety is involved. It is being used to call attention to POTENTIAL 
hazards that could result in personal injury or loss of life.

IMPORTANT SAFETY INSTRUCTIONS

24-inche

s (0.60 m)

24-inche

s (0.60 m)

24-inche

s (0.60 m)

Содержание M3i lite





















Отзывы: