Kebby BenchMark Скачать руководство пользователя страница 28

Страница: 28 / 30

WARNINGS:

If the

BenchMark

is not set up properly for the vial size and seal type that is to be crimped,

there is a chance of vial breakage during the crimp cycle. As a precaution, the following
checks should be made prior to operating the

BenchMark



Make sure the correct Vial Holder and Head are assembled to the

BenchMark



Make sure all four settings are correct for the vial size and seal type to be
crimped (refer to settings recorded during the initial setup).

Wear impact resistant safety glasses and protective gloves while operating the

BenchMark

OPERATING INSTRUCTIONS

CRIMPING OPERATION

INSTRUCTIONS

Place a seal on a filled vial and set
the vial on the Vial Holder so that it
is up against the Vial Stop (A).

Pull the Crimp Lever (B) forward as
far as it will go, then gently allow
the Crimp Lever to return to its
original position.

Remove the sealed vial from the
Vial Holder.

Repeat steps A through C until all
vials have been sealed.

Содержание BenchMark































Результаты поиска

Содержание BenchMark

Отзывы:

Похожие инструкции для BenchMark

Бренды по названию

Популярные бренды

Kebby BenchMark, Руководство по установке и эксплуатации

Результаты поиска

Содержание BenchMark

Отзывы:

Похожие инструкции для BenchMark

Бренды по названию

Популярные бренды