Kaufman & Robinson eHC 15015A Скачать руководство пользователя страница 65

Страница: 65 / 67

8-2 APPENDIX

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

6. The display should now be alternately

ashing CP4 and 10. This is the cath-

ode purge value. The number 10 is the

ow in sccm that

ows even when

the Auto Controller is in standby if either the Auto Gas or Manual Gas Op-

erating Mode are selected. Use the Gas Adjust knob to dial in the desired

purge gas

ow, or dial in 0 if no purge gas is desired. When

nished, press

and release the Operating Mode button.

7. The display should now read b, followed by a number. This controls how

many times the Auto Controller beeps if the operating parameters have

been changed without saving them, or when a fault occurs. Turn the Gas

Adjust knob to select the desired number of beeps. When

nished, press

and release the Operating Mode button.

8. The display should now be alternating between P35 and 0 or 1. This deter-

mines the functionality of pin 35 on the DB35 connector. When set to 0, pin

35 serves as the gas ratio pin. When set to 1, this pin allows selection of

the gas only mode from the rear panel. When set to 2, this allows the user

to remotely switch from local to remote by means of grounding pin 35 to pin

7 or 8.

9. The display should now be alternately

ashing d25 and the number 1 or 2.

This controls the DB25 analog I/O for the mark I or Mark II power supplies.

Turn the Gas Adjust knob to either 1 for Mark I or 2 for Mark II I/O. When

nished, press and release the Operating Mode button.

The Auto Controller has now been con

gured and is ready to use.

Содержание eHC 15015A




































































Результаты поиска

Содержание eHC 15015A

Отзывы:

Бренды по названию

Популярные бренды

Kaufman & Robinson eHC 15015A, Руководство пользователя

Результаты поиска

Содержание eHC 15015A

Отзывы:

Бренды по названию

Популярные бренды