Kaufman & Robinson eHC 15015A Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 67

Kaufman & Robinson eHC 15015A Скачать руководство пользователя страница 30

INITIAL OPERATION 4-11

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

Manual Gas mode operates the same as the auto gas mode except that

there is no feedback loop for the gas

fl

ows to maintain the anode param-

eters. This being the case, the gas channels can all be independently ad-

justed during operation, where this was not possible in the Auto Gas mode.

The discharge parameters can be set up for either constant voltage mode

operation or constant current mode operation as described above for the

manual gas operating mode.

Constant voltage mode is typically used for discharge voltages of 120 volts

or more. The discharge current is usually set to maximum, while the operat-

ing voltage is set to the desired value on the front panel. The gas

fl

ow to the

ion source is then adjusted to control the ion source current.

Constant current mode is typically used for discharge voltages less than

120 volts. The discharge voltage is usually set to maximum, while the oper-

ating current is set to the desired value on the front panel. The gas

fl

ow to

the ion source is then adjusted to control the ion source voltage.

Select the Manual Gas mode using the Operating Mode button. Select

the program to run using the Program Select button. Enable the program

by pressing the Enable/Standby button on the Auto Controller. Press the

Enable/Standby button again to stop the program and put the units into

Standby.

Saving a program is the accomplished in the same manner as described

above for the Auto Gas and Gas Only operating modes.

«
...
28
29
30
31
32
...
»

Содержание eHC 15015A




































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды