Kaufman & Robinson eHC 15015A Скачать руководство пользователя страница 24

Страница: 24 / 67

INITIAL OPERATION 4-5

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

vacuum facility pump speed or other process that take place while the

ion source is running.

4.3.1.7 Standby

Press and release the white Enable/Standby button on the front panel of

the Auto Controller. Notice that the yellow Standby LED under the button

turns on and the green Enable LED above the button turns off. The same

LED transition from Enable to Standby also happens on the three power

supplies as the Auto Controller sequences them off.

The auto controller updates the program and saves a new starting gas

ow so the discharge parameters will be reached more quickly the next

time the program is run.

4.3.1.8 Setpoint Adjustment

When the Auto Controller is in the Auto Gas mode, the ion source

parameters can be adjusted before the auto controller is enabled as

described above. When the values are adjusted, the program LED will

ash to indicate that the program has not been saved. The new values

can be acquired by pressing and holding the acquire setpoints button

until the program LED stops

ashing.

Once the controller is enabled, the discharge voltage and current can be

adjusted. Adjusting the discharge current when the auto controller is

enabled also adjusts the Emission current. In this case, the Emission

current becomes a

xed ratio of the Emission current to discharge

current based on the Emission and discharge current setpoints before

the Auto Controller was enabled. For example: The discharge current

and Emission current are set to 4.0 amps and 4.4 amps before enabling

the auto controller; after enabling, the discharge current is adjusted to

5.0 amps and the Emission current will automatically be adjusted to 5.5

amps. Press and hold the acquire setpoints button until the program

indicator stops

ashing to acquire the new setpoints; the old program

values will be overwritten with the new values. Pressing the program

button once before new values are acquired will clear any adjustments

and revert back to the original program.

4.3.1.9 Saving a Program

The

rst step is to select the operating condition. Review the ion source

manual to select an operating condition that is within the range of the

Содержание eHC 15015A




































































Результаты поиска

Содержание eHC 15015A

Отзывы:

Бренды по названию

Популярные бренды

Kaufman & Robinson eHC 15015A, Руководство пользователя

Результаты поиска

Содержание eHC 15015A

Отзывы:

Бренды по названию

Популярные бренды