Kaufman & Robinson eHC 15015A Скачать руководство пользователя страница 29

Страница: 29 / 67

4-10 INITIAL OPERATION

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

• Use the white Select button on the Discharge Power Supply to se-

lect Volts. Turn the knob on the Discharge Power Supply until the

discharge voltage is set to 150 volts as indicated on the Discharge

Volts display.

• Press the white Enable/Standby button on the Keeper Power Sup-

ply. And wait a couple of seconds for the keeper to start the hollow

cathode as indicted by the Keeper Amps display reading 1.5 amps.

• Reduce the

ow to gas channel 4 to 10 sccm.

• Press the white Enable/Standby button on the Emission Power Sup-

ply.

• Press the white Enable/Standby button on the Discharge Power

Supply.

• Adjust the gas

ow for channel 1 using the Gas Adjust Knob on the

Auto Controller until the discharge current is approximately 2.5 A.

• Operate the ion source for at least 10 minutes to clean any contami-

nates from the ion source that may have been introduced while at

atmosphere.

• The discharge current will vary slightly during this time. Adjust the

gas

ow after the 10 minutes to obtain a discharge current of ap-

proximately 2.5 A.

• At this point the operating conditions can be saved as a program to

be used later in the Auto Gas mode or the Manual Gas mode. To do

this press and hold the white Acquire Setpoints button for two sec-

onds. This saves the new parameters to the active program.

• Stop operation by putting the discharge, emission and keeper pow-

er supplies into Standby in that order by pressing the white Enable/

Standby button on each controller.

• Put the gas

ow into Standby by pressing the white Enable/Standby

button on the auto controller.

4.3.3 Manual Gas Mode

Содержание eHC 15015A




































































Результаты поиска

Содержание eHC 15015A

Отзывы:

Бренды по названию

Популярные бренды

Kaufman & Robinson eHC 15015A, Руководство пользователя

Результаты поиска

Содержание eHC 15015A

Отзывы:

Бренды по названию

Популярные бренды