manualshive.com logo in svg

Kaufman & Robinson eHC 15015A, Руководство пользователя

Поделиться
Скачать
Kaufman & Robinson eHC 15015A Скачать руководство пользователя страница 17

3-6                                                                                                    INSTALLATION

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

Pin

Number

Description

13

Not used.

14

Chassis Ground.

15

Not used.

3.5 Connect Controller to Ion Source

If the Ion Source has not been installed in the vacuum chamber, do so now, 

using the Installation/Inspection description in the ion source manual. The ion 

source installation procedures cover installation of the ion source, vacuum 

cables, gas tubing inside the vacuum chamber, as well as electrical and gas 

feedthroughs in the wall of the vacuum chamber. Once installed, connect the 

operating cable to the electrical feedthrough.

• As the 

fi

 nal installation step, turn off the front panel power switches on the 

Auto Controller, Keeper Power Supply, Emission Power Supply and Dis-

charge Power Supply and then plug the power cables of the individual con-

trollers into appropriate input power sources. See table 3-1 above for input 

power requirements.

The installation for the automated power controller is now complete.

Содержание eHC 15015A




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды