manualshive.com logo in svg

Kaufman & Robinson eHC 15015A, Руководство пользователя

Поделиться
Скачать
Kaufman & Robinson eHC 15015A Скачать руководство пользователя страница 41

6-8                                                                   REMOTE/AUTOMATED CONTROL

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

Pin 

Number

Description

15

Gas Channel 4 shut off. Connecting this pin to common pin 7 or 8 will 
disable the gas 

fl

 ow to the MFC and deactivate the additional MFC 

relay for channel 4, regardless of the input 

fl

 ow setting.

16

Program Select 0. This pin is the 0 bit for selecting programs 1 
through 4 using negative logic levels of 0 and 5 volts or 8, the remote 
setpoints are enabled and the four programs are not used.

18

DB-37 control select. The pin is connected to common pin 7 or 8 to 
enable the DB-37 connector. When the connection is left open, the 
DB-25 is active.

19

Run Fault. When the Auto Controller is enabled, this pin will indicate a 
run fault if it is at a high logic level of 5 volts. If there is no run fault, then 
this pin will be at a low logic level of 0 volts. Referenced to pin 7 or 8.

20

Discharge Current Output. 0-5 volts corresponds with 0 to the maxi-
mum level of discharge current in amps for the Discharge Power Sup-
ply that is being used.

21

Discharge Voltage Output. 0-5 volts corresponds with 0 to the maxi-
mum level of discharge voltage in volts for the Discharge Power Sup-
ply that is being used.

22

Discharge Current Setpoint. 0-5 volts corresponds with 0 to the maxi-
mum level of discharge current in amps for the Discharge Power Sup-
ply that is being used.

23 

Beam Good 1. Shorted to pin 24 when the operating parameters are 
in range.

24

Beam Good 2. Shorted to pin 23 when the operating parameters are 
in range.

25

Keeper voltage output. 0-5 volts corresponds with 0-800 volts. Refer-
enced to common pin 7 or 8.

26

Keeper Current Setpoint. 0-5 volts corresponds with 0 – 2 amps. This 
should usually be set to 1.5 amps

27

Gas 

fl

 ow Output common. Return for gas 

fl

 ow output pins 8, 9, 28 and 

29.

28

Channel 2 gas 

fl

 ow Output. 0-5 volt corresponds with 0 to the maxi-

mum output in sccm for the channel 2 MFC. Referenced to pin 27.

29

Channel 4 gas 

fl

 ow Output. 0-5 volt corresponds with 0 to the maxi-

mum output in sccm for the channel 4 MFC. Referenced to pin 27.

30

Channel 2 setpoint. 0-5 volts corresponds with 0 to the maximum out-
put for the MFC connected to Channel 2. Referenced to pin 13.

Содержание eHC 15015A




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды