Kanga PW628 Скачать руководство пользователя страница 68

Страница: 68 / 69

TROUBLE

PROBABLE CAUSE

REMEDY

Engine will not crank over.

Low battery output.

Recharge or replace battery.

Loose, disconnected or broken
battery cables.

Inspect cable(s) and tighten all
connections. Repair or replace
cables as necessary.

Faulty Starter.

Repair or replace starter.

Faulty circuit wiring.

Check wiring continuity.

Engine

ooded (petrol).

Remove spark plug and crank.

Engine cranks but not

res.

No fuel in tank.

ll fuel tank.

Spark plug fouled (petrol engines).

Check spark plug gap and clean or
replace spark plug.

Dirty fuel

lter.

Clean

lter.

Carburettor

ood (petrol engines).

Clear carburettor.

Fuel valve closed.

Open valve.

Engine runs but stalls.

Spark plug fouled (petrol engines).

Check spark plug gap & clean or
replace.

Fuel valve closed.

Open valve.

Low battery output.

Recharge or replace battery.

Power take-off engaged

Shift power take-off lever
into neutral.

ENGINE

Содержание PW628






































































Результаты поиска

Содержание PW628

Отзывы:

Похожие инструкции для PW628

Бренды по названию

Популярные бренды

Kanga PW628, Руководство оператора

Результаты поиска

Содержание PW628

Отзывы:

Похожие инструкции для PW628

Бренды по названию

Популярные бренды