Kanga PW628, Руководство оператора

Страница: 39 / 69

38
BUCKET BROOM OPERATING INSTRUCTIONS
1. Connect the attachment plate of the loader to the Bucket
Broom frame ensure the quick hitch / attachment locking
pins are engaged.
2. Turn the engine off, move the Aux Lever 3 back and forth to
release hydraulic pressure. Ensure the QRC’s are clean then
connect the hoses of the Bucket Broom to A & B QRC’s on
the right hand side of the loader when looking from the front
of the machine.
3. Connect the hose bracket to the machine and secure the
R Clip.
4. Install the chain onto the broom chain clamp (Supplied with
the Broom) around the top of the lift arm cylinder and tighten
onto the machine.
5. Place the bucket broom fl at on the ground and adjust the
chain to have about 4 links slack so when you lift the bucket
up and tilt it forward it will open the bucket lid and empty out
the debris.
6. To Remove the Bucket Broom please reverse the
instructions above.
PLEASE NOTE: ALWAYS FIT THE DUST CAPS PROVIDED FOR
THE QRC’S TO YOUR ATTACHMENT AND MACHINE WHEN
NOT IN USE TO PREVENT DIRT ENTERING THE SYSTEM.
1. Ensure Lever 3 is in neutral.
2. Start the Engine and adjust the Engine RPM Lever 7 to suit
the operation power you require.
3. Position the Bucket fl at on the ground engage Lever 3 and
pull towards the operator. This will start the Broom rotating
and sweeping into the bucket base.
4. The Bucket can either be pulled or pushed with the mini
loader drive system however the does work more ef fi ciently
when pulled.
5. Using levers 4 & 5 Drive the machine, Travel Speed is
controlled by levers 4 & 5 by gently engaging both levers
forward, The further forward they are the faster the machine
will travel and slowing down is the exact reverse allowing the
levers to gently return to centre will slow the machine down.
6. To empty debris from the bucket disengage Lever 3 tilt back
slightly and drive to the location you would like to dump the
debris, Raise the lift arm with Lever 2 and tilt the bucket
forward to dump the debris out using Lever 6.
CAUTION: Prior to commencing work, read the
Safety Rules of this Kanga Loader Manual.
FITTING THE ROTARY HOE
OPERATING INSTRUCTIONS:
39
ROTARY HOE OPERATING INSTRUCTIONS
FITTING THE ROTARY HOE
1. Connect the attachment plate of the loader to the Rotary
Hoe ensure the quick hitch/attachment locking pins
are engaged.
2. Turn the engine off, move the Aux Lever 3 back and forth to
release hydraulic pressure. Ensure the QRC’s are clean then
connect the hoses of the Rotary Hoe to A & B QRC’s on the
right hand side of the loader when looking from the front of
the machine.
3. Connect the hose bracket to the machine and secure the
R Clip.
4. To Remove the Rotary Hoe please reverse the
instructions above.
PLEASE NOTE: ALWAYS FIT THE DUST CAPS PROVIDED FOR
THE QRC’S TO YOUR ATTACHMENT AND MACHINE WHEN
NOT IN USE TO PREVENT DIRT ENTERING THE SYSTEM
1. Ensure the Rotary Hoe is securely attached to the
Kanga Loader.
2. Check that the couplings are engaged and check all joins
for leaks.
3. Tighten and repair and required.
4. Check the rotary hoe and cutting blades are in
good condition.
1. Ensure Lever 3 is in neutral.
2. Start the Engine and adjust the Engine RPM Lever 7 to suit
the operation power you require.
3. Position the Rotary Hoe fl at on the ground and engage Lever
3 and pull towards the operator to start the blades rotating.
4. The Rotary Hoe should only be pulled with the mini loader
drive system. Using Levers 4 & 5 to drive the machine. Travel
Speed is controlled by levers 4 & 5 by gently engaging both
levers Rearward. The further Rearward they are the faster
the machine will travel and slowing down is the exact reverse
allowing the levers to gently return to centre will slow the
machine down.
5. The travel speed of the loader will adjust the condition of the
soil, slower travel speed will turn the soil over more making
it softer. Fast speed will turn the soil over less allowing for a
Chunkier texture.
PRE - OPERATION CHECK
OPERATING INSTRUCTIONS:
CAUTION: Prior to commencing work, read the
Safety Rules
of this Kanga Loader Manual.