Kanga PW628 Скачать руководство пользователя страница 55

Страница: 55 / 69

SERVICE TASKS - PIVOT PINS

BOTTOM PIVOT PINS

Before every use, visually inspect all pivot pins for any signs of wear and damage or possible failure.
Thoroughly inspect all pivot pins and bushes for wear and damage at an interval of 200
operating hours.

Part No.

0K10800

Part No.

0K10903

0K10700

PIN A (44MM) KIT

x 2

0K10800

PIN B (51MM) KIT

x 3

0K10810

PIN D (55MM) KIT

x 2

0K10900

PIN C (60MM) KIT

x 2

0K10903

PIN G (65MM) KIT

x2 Piston End

L111210

BUSH IRB 1610

x 2

L111410

TOP BUSH IRB 1616

x 5

SERVICE TASKS - TYRES & PRESSURE

MID RANGE

TYRE 23 X 850 X 12 LUG

Part Number-L114105

TYRE 23 TURF KENDA 23 X 10-5 X 12

Part Number-L114106

TUBELESS VAL 10-12 RIM

Part Number-DL-000995

7 X 12 RIM COMPLETE

Part Number-0K14206

NUTS WHEEL 7/16 UNF

Part Number-FA-000530

STUD WHL 7-16 KNOCK-IN

Part Number-DL-000458

Visually check tyres on a daily basis and check tyre pressure every 50 operating hours, and check
for wear and damage to tyres and tracks.

Tyre pressures

KANGA LOADER TYRE PRESSURES GROSS

Tyre

Size

Recommended

Pressure

Gross weight Kgs

(Water Filled)

KPA

PSI

Lug 23”

23 X 8.5 X 12

260

Turf 23”

23 X 8.5 X 12

150

Содержание PW628






































































Результаты поиска

Содержание PW628

Отзывы:

Похожие инструкции для PW628

Бренды по названию

Популярные бренды

Kanga PW628, Руководство оператора

Результаты поиска

Содержание PW628

Отзывы:

Похожие инструкции для PW628

Бренды по названию

Популярные бренды