Kaliburn SR-100i Скачать руководство пользователя | Manualshive

Страница: 12 / 75

background image

Safety

SR-100i User’s Manual

any type of oil or grease.

•

Never use a compressed gas cylinder or pressure regulator for any purpose
other than which it is intended.

•

Never use a pressure regulator for any gas other than which it is intended.

•

Never use a pressure regulator that is leaking or has other signs of physical
damage.

•

Never use oxygen hoses and pressure regulators for any gas other than
oxygen.

•

Never use any gas hose that is leaking or has other signs of physical damage.

Health Support Equipment

The SR-100i system creates electric and magnetic fields that may interfere with
certain types of health support equipment, such as pacemakers. Any person who
uses a pacemaker or similar item should consult a doctor before operating,
observing, maintaining, or servicing the SR-100i system. Observe the following
guidelines to minimize exposure to these electric and magnetic fields:

•

Stay as far away from the SR-100i power supply, torch, torch leads, and
remote high frequency console as possible.

•

Route the torch leads as close as possible to the work ground cable.

•

Never place your body between the torch leads and work ground cable. Keep
the work ground cable and the torch leads on the same side of your body.

•

Never stand in the center of a coiled up set of torch leads or work ground
cable.

Safety Standards Booklet Index

For further information concerning safety practices to be exercised with plasma
arc cutting equipment, please refer to the following publications:

1.

AWS Standard AWN,

Arc Welding and Cutting Noise

, obtainable from the

American Welding Society, 550 NW LeJeune Road, Miami, FL 33126.

2.

AWS Standard C5.2,

Recommended Practices for Plasma Arc Cutting

,

obtainable from the American Welding Society, 550 NW LeJeune Road,
Miami, FL 33126.

3.

AWS Standard FSW,

Fire Safety in Welding and Cutting

, obtainable from

the American Welding Society, 550 NW LeJeune Road, Miami, FL 33126.

4.

AWS Standard F4.1, Recommended

Safe Practices for Preparation for

Welding and Cutting of Containers and Piping

, obtainable from the

American Welding Society, 550 NW LeJeune Road, Miami, FL 33126.

1-4

«
...
10
11
12
13
14
...
»

Содержание SR-100i












































































Отзывы:

Нет отзывов

Похожие инструкции для SR-100i

WIRELESS ALARM SYSTEM

Бренд: Abus Страницы: 14

Бренд: Abus Страницы: 11

Бренд: Abus Страницы: 82

Бренд: Abus Страницы: 16

WIRELESS ALARM SYSTEM

Бренд: Abus Страницы: 101

Бренд: Caddx-Caddi Controls Страницы: 6

Split Vision VSLR3

Бренд: Federal Signal Corporation Страницы: 4

Бренд: GAL Страницы: 2

Бренд: GE Страницы: 28

Бренд: Magnavox Страницы: 24

Бренд: Hailo Страницы: 104

Бренд: Halo Smart Labs Страницы: 34

Бренд: Manitou Systems Страницы: 244

Бренд: C&K systems Страницы: 8

Бренд: Bowers & Wilkins Страницы: 1

Бренд: Legacy Страницы: 23

Бренд: WilTec Страницы: 4

Бренд: SecurityMan Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды