manualshive.com logo in svg

Kaliburn SR-100i, Руководство пользователя

Поделиться
Скачать
Kaliburn SR-100i Скачать руководство пользователя страница 48

Maintenance and Troubleshooting                                                               SR-100i User’s Manual 

 

220/380V 50 Hz TRANSFORMER CONFIGURATIONS

 

 

220V 50 Hz and 380V 50 Hz power supplies are shipped with a dual voltage main 
transformer TR1.  The primary taps on TR1 are labeled with their corresponding 
voltages.  To change the operating voltage for these systems, perform the 
following procedures. 
 

220V 50Hz Operation

 

For 220V operation, install a #8 AWG jumper wire from 220V on the first 
primary winding to 0V on the second primary winding.  Install a second #8 AWG 
jumper wire from 220V on the second primary winding to 0V on the third primary 
winding.  Install a third #8 AWG jumper wire from 220V on the third primary 
winding to 0V on the first primary winding.  Connect the three phase primary 
power from the main contactor to the 220V connection on each primary winding.  
See Figure 7-3.

  When the primary voltage of TR1 is changed, the control 

transformer TR2 must also be rewired for the correct service voltage

.  For 

220V operation, connect the white wire of control transformer TR2 to TB2-13, 
connect the brown wire to TB2-14, and connect a wire (#20 AWG minimum) 
from the side terminal of fuse F1 to TB2-14.

 

 

 

380V 50Hz Operation

 

For 380V operation, install a #8 AWG jumper wire from 0V on the first primary 
winding to 0V on the second primary winding.  Install a second #8 AWG jumper 
wire from 0V on the second primary winding to 0V on the third primary winding.  
Connect the three phase primary power from the main contactor to the 220V 
connection on each primary winding.  See Figure 7-4.  

When the primary 

voltage of TR1 is changed, the control transformer TR2 must also be rewired 
for the correct service voltage

.  For 380V operation, connect the white wire of 

control transformer TR2 to TB2-13, connect the brown wire to TB2-14, and 
connect the gray wire to the side terminal of fuse F1. 
 
 
 
 
 
 
 
 
 
 
 
 

 

5-6 

Содержание SR-100i












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды