manualshive.com logo in svg

Kaliburn SR-100i, Руководство пользователя

Поделиться
Скачать
Kaliburn SR-100i Скачать руководство пользователя страница 30

Operation 

                                              SR-100i User’s Manual 

 

 

 

Figure 4-1  Front Panel Controls 

 
 

Mechanized Cutting Mode

 

 

To place the SR-100i in the mechanized cutting mode, set the Mode Switch 
thumbwheel to position number 2.  The start signal initiates the following 
sequence of events: 
 

1.

 

Two-second gas preflow. 

2.

 

Pilot arc initiation. 

3.

 

Transferred arc establishes (cutting arc). 

4.

 

X/Y machine motion signal enabled.  Note that the machine motion 
signal can be delayed for up to three seconds using the motion delay 
potentiometer on the front panel.  

 
Removal of the plasma start signal terminates cutting, disables the x/y machine 
motion signal, and initiates gas postflow.  Note:  Loss of the cutting arc, even if 
a plasma start signal is applied, deenergizes the SR-100i system, disables the x/y 
machine motion signal, and initiates postflow of gas.  Reapplying the plasma 
start signal while in the gas postflow stage will initiate the cutting arc 
immediately, without going through the gas preflow sequence. 

 

Manual Cutting Mode

 

 

To place the SR-100i in the manual cutting mode, set the Mode Switch 
thumbwheel to position number 0.  The manual cutting mode is used when it is 
necessary to automatically reestablish a lost cutting arc.  For example, if the torch 
is going to cross a pre-cut kerf during a cutting sequence, the arc may be lost.  In 
mode 0, the pilot arc relay will automatically close and the arc will be reignited. 
 
The sequence for initiating the arc is the same as in the mechanized cutting mode.  
However, when the cutting arc is lost, the pilot arc is reestablished with 
continuous high frequency and will remain in the pilot arc high frequency state 
until a cutting arc is reestablished.  The x/y machine motion signal will remain 

 

4-2 

Содержание SR-100i












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды