Kaliburn SR-100i страница 44 Скачать руководство пользователя | Manualshive

Страница: 44 / 75

background image

Maintenance and Troubleshooting SR-100i User’s Manual

Monthly Procedures

Note: At minimum, these checks should be performed on a monthly basis.

In excessively dirty environments or in heavy usage situations, the checks

should be performed more frequently.

** WARNING **

Remove primary power from the system before performing the following

procedures

SR-100i Power Supply

1.

Remove the rear panel of the power supply.

2.

Verify that all torch lead connections and work ground connections are secure.

Only tighten the gas fittings enough to make a gas seal. The fittings are
subject to damage if over tightened

.

3.

Verify that the primary AC connections are tight.

4.

Remove the left and right side panels and blow out the power supply cabinet
with clean, dry, compressed air. Be sure to blow off all circuit bards.

5.

Verify that all p.c. board connectors are installed securely.

6.

Verify that the rear panel Amp connectors are installed securely.

7.

Check the pilot arc relay contacts for signs of pitting and replace if necessary.

8.

Verify that all hardware connections are tight.

9.

Clean and reset the spark gap spacing to .018” (.46 mm).

10.

Check the connection of the high frequency coupling transformer leads to the
I/O p.c. board.

11.

Verify that the fan blades spin freely.

SR-100i Torch Leads

1.

Verify that all torch lead connections are secure.

Only tighten the gas

fittings enough to make a gas seal. The fittings are subject to damaged if
over tightened.

2.

Remove the retaining cap and consumables from the torch.

3.

Using an ohmmeter, measure zero ohms between the power supply Torch
Minus connector on the I/O p.c. board and the cathode body inside the torch.
The cathode body is the brass piece that the electrode seats against.

4.

Using an ohmmeter, measure zero ohms between the power supply Pilot Arc
connector on the I/O p.c. board and the torch anode body. The anode body is
the brass piece that the retaining cap threads onto.

5.

Verify that the braided shield of the torch leads is secured to the brass adaptor
that connects to the power supply. Also, make sure the adaptor is secured
tightly to the power supply enclosure. Using an ohmmeter, measure zero
ohms between the braided shield and the ground stud on the power supply
sub-panel.

6.

Inspect the braided shield and torch lead hoses for cuts or other signs of

5-2

«
...
42
43
44
45
46
...
»

Содержание SR-100i












































































Отзывы:

Нет отзывов

Похожие инструкции для SR-100i

Бренд: FAAC Страницы: 14

Бренд: Omni Страницы: 108

Бренд: quadient Страницы: 5

Бренд: quadient Страницы: 5

Бренд: BST Pro Страницы: 9

Бренд: BlitzRotary Страницы: 41

kb sound Series

Бренд: EIS Страницы: 2

Бренд: Mark Climate Страницы: 60

Бренд: Magnavox Страницы: 12

Бренд: Audiocenter Страницы: 40

NeverFreeze SX-0810-24

Бренд: ThermoSoft Страницы: 5

Бренд: Duevi Страницы: 19

Surveillance Detector

Бренд: Mini Gadgets Страницы: 2

Бренд: quadient Страницы: 5

Бренд: urmet domus Страницы: 8

Бренд: MAC TOOLS Страницы: 40

Бренд: Daikin Страницы: 9

Бренд: Lorex Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды