manualshive.com logo in svg

Kaliburn SR-100i, Руководство пользователя

Поделиться
Скачать
Kaliburn SR-100i Скачать руководство пользователя страница 23

Installation

 

                                              SR-100i User’s Manual

 

 

Power Supply Output Connections

 

 

 
Perform the following steps to connect the output of the power supply to the torch 
leads and the work table.  See Figure 3-2 for additional information. 
 

Note:  When making hose connections, only tighten the brass 

fittings enough to make a gas seal.  The fittings are 

subject to damage if over tightened. 

 

Torch Leads 

1.

 

Remove the threaded ring from the brass shield connector on the end of the 
braided shield. 

1 

 
2.

 

Route the torch leads through the opening in the rear of the power supply and 
push the shield connector through the hole until it is seated against the sheet 
metal. 

 
3.

 

Slide the threaded ring over the torch leads and thread onto the shield 
connector.  

Tighten the threaded ring firmly.

  The shield connector grounds 

the braided shield to the power supply enclosure to help eliminate high 
frequency noise emission.  Using an ohmmeter, measure zero ohms between 
the braided shield and the ground stud on the sub-panel inside the power 
supply. 

 
4.

 

Connect the torch electrode lead (3/8” hose) to the Torch Electrode fitting on 
the I/O board. 

 
5.

 

Connect the torch nozzle lead (3/16” hose) to the Torch Nozzle fitting on the 
I/O board. 

 
 

Work Ground Lead

 

1.

 

Route one end of the #4 AWG work ground lead through the bushing on the 
lower rear of the power supply and connect it to the Work Ground connection 
on the I/O board. 

2 

 

2.

 

Connect the other end of the work ground lead to the star ground point on the 
cutting table.  The star ground point is generally referred to as the common 
ground point on the cutting table where all subsystems of the machine are 
grounded.  This point is then connected to a driven earth ground rod that 
should be as close as possible to the star ground.  The ground rod should have 
no other wires connected to it.  The ground rod should be at least 3/4 inches in 
diameter and should be driven into the earth’s permanent moisture layer.  The 
length of the ground rod varies from installation to installation and should be 
installed according to local and national codes.  Refer to the National 
Electrical Code, Article 250, Section H, Ground Electrode System for 
additional information. 

 

3-3 

Содержание SR-100i












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды