Kaliburn Spirit200a Скачать руководство пользователя

Страница: 60 / 164

Operation

Spirit200a User’s Manual Rev J

This information is subject to the controls of the Export Administration Regulations [EAR]. This information shall not be provided to

non-U.S. persons or transferred by any means to any location outside the United States contrary to the requirements of the EAR.

4-18

Installing or Removing Torch Consumables

Turn off the plasma power supply before continuing with this procedure.

Note: When installing the consumables, do not use an excessive

amount of o-ring lubricant. Also ensure that the lubricant is placed

only on the o-rings. Excess lubricant can interfere with gas flow,

which can cause starting problems, poor cut quality, and short

consumable life.

Note: Do not over tighten the consumables! Only tighten until the

parts are seated properly.

1. Unthread the quick-disconnect torch head from the torch base by

turning the attachment ring to the RIGHT.

2.  Remove the outer retaining cap from the torch head.
3.  Remove the inner retaining cap from the torch head.
4.  Separate the shield cap from either the inner retaining cap or the outer

retaining cap.

5. Use the nozzle removal tool (P/N 277056) to remove the nozzle from

the torch head. To do this, insert the tool into the groove on the nozzle

and hold the tool/nozzle in the palm of your hand. Pull both hands

apart using a linear motion as in the left image below. Do not use a

prying or bending motion as in the right image below.

CORRECT

INCORRECT!

6. Use the swirl ring removal tool (P/N 260105) to remove the swirl ring

from the nozzle.

PULL

Содержание Spirit200a





































































































































































Результаты поиска

Содержание Spirit200a

Отзывы:

Похожие инструкции для Spirit200a

Бренды по названию

Популярные бренды

Kaliburn Spirit200a, Руководство пользователя

Результаты поиска

Содержание Spirit200a

Отзывы:

Похожие инструкции для Spirit200a

Бренды по названию

Популярные бренды