Kaliburn Spirit200a Скачать руководство пользователя

Страница: 32 / 164

Installation

Spirit200a User’s Manual Rev J

This information is subject to the controls of the Export Administration Regulations [EAR]. This information shall not be provided to

non-U.S. persons or transferred by any means to any location outside the United States contrary to the requirements of the EAR.

3-10

Torch Leads to Torch Base Connections

Perform the following steps to connect the torch leads to the torch base.

Note: When making hose connections, only tighten the brass fittings

enough to make water or gas seals. The fittings are subject

to damage if over tightened. Also, use two wrenches when

tightening the torch fittings to avoid damaging the torch

Torch Handle Installation

1. Route the torch leads through the torch handle. Note that the threaded

end of the torch handle mates with the torch base.

Torch Electrode/Coolant Supply Lead

•

Connect the torch electrode/coolant supply lead to the torch base as

shown.

Torch Coolant Return Lead

•

Connect the torch coolant return lead to the torch base as shown.

Note that the torch coolant return lead fitting has left hand threads.

Torch Nozzle Lead

•

Connect the torch nozzle lead to the torch base as shown.

Torch CTP Sensor Lead

•

Connect the torch CTP sensor lead to the torch base as shown.

Содержание Spirit200a





































































































































































Результаты поиска

Содержание Spirit200a

Отзывы:

Похожие инструкции для Spirit200a

Бренды по названию

Популярные бренды

Kaliburn Spirit200a, Руководство пользователя

Результаты поиска

Содержание Spirit200a

Отзывы:

Похожие инструкции для Spirit200a

Бренды по названию

Популярные бренды