Kaliburn Spirit200a Скачать руководство пользователя страница 129

Страница: 129 / 164

Maintenance and Troubleshooting

Spirit200a User’s Manual Rev J

This information is subject to the controls of the Export Administration Regulations [EAR]. This information shall not be provided to

non-U.S. persons or transferred by any means to any location outside the United States contrary to the requirements of the EAR.

7-7

Troubleshooting Using the Control Panel Status LED’s

If the Spirit system develops a problem, first check the control panel status

LED’s. If one or more of the LED’s does not illuminate after the ON button

is depressed, use the status LED’s to pinpoint the problem.

•

RHF Door LED

- Extinguishes when the RHF door switch opens.

Check the RHF door, switch, and associated wiring.

•

Gas Console LED

- Extinguishes when there is a problem with the

gas console or when the unit is adjusting gas pressures. Switch to the

messages screen on the gas console to pinpoint the problem.

•

3 Phase Power LED

- Extinguishes when there is a problem with the

three phase power being supplied to the chopper assembly. Verify

that the primary wall disconnect fuses are good and check the main

transformer, main contactor and A.C. Detect p.c. board for proper

operation. Also, this LED should turn on immediately when the green

“ON” button is pressed. If not, check P28-3 to P28-4 for 10 VDC first.

This should drop to 0 VDC when the ON button is pushed. If not, then

check CR1 and associated wiring.

•

Coolant Flow LED

- Extinguishes when there is a problem with the

torch coolant system. Check the coolant pump fuse F2 and verify that

230VAC is present between TB3-13 and TB3-14. Also check for clogs

in the coolant leads and coolant filter/deionization cartridge.

•

Coolant Level LED

- Extinguishes when the coolant level in the tank

has dropped below the required minimum level. Add more coolant to

clear the error.

•

Coolant Temperature LED

- Extinguishes when the coolant

temperature has risen above the maximum operating temperature.

Ensure that the heat exchanger fan is running and that the heat

exchanger is free from dust. Blow out the heat exchanger and fan with

clean, dry, oil-free compressed air. Leave the unit running until the

LED illuminates.

Содержание Spirit200a





































































































































































Результаты поиска

Содержание Spirit200a

Отзывы:

Бренды по названию

Популярные бренды

Kaliburn Spirit200a, Руководство пользователя

Результаты поиска

Содержание Spirit200a

Отзывы:

Бренды по названию

Популярные бренды