manualshive.com logo in svg

kaarta STENCIL 2, Руководство пользователя, Страница: 113 / 147

Поделиться
Скачать
kaarta STENCIL 2 Скачать руководство пользователя страница 113

 

113 

•

 

Always_on_top:

 

true – controls whether the GPS monitor window is always on top of 

any other display window.

 

•

 

delete_file_if_empty:

 true 

– This parameter will delete a gps file after scanning if 

the file was created but contains no data.

 

sensorOffsets: 

Offsets between the GNSS unit and the lidar on Stencil 2. The ones listed 

here are for the Emlid Reach+ as mounted using Kaarta’s GNSS mounting bracket.

 

•

 

lidarToGNSS_Left:

 0.0 

•

 

lidarToGNSS_Up:

 0.1208 

•

 

lidarToGNSS_Forward:

 0.0 

The following are the default offsets for the feature tracker being used in Stencil. These 
parameters can be uncommented and changed to reflect a different feature tracker mounting 
position for live scanning and replay.  

•

 

#  

camToLidar_Left:

 -0.0825 

•

 

#  

camToLidar_Up:

 0.0785 

•

 

#  

camToLidar_Forward:

 -0.0365 

•

 

#  

camToLidar_Roll:

 0.0 

•

 

#  

camToLidar_Pitch:

 0.0 

•

 

#  

camToLidar_Yaw: 

0.0 

image_saver: 

•

 

save_interval:

 1.0 – 

Time in seconds between images. 

•

 

max_image_width:

 

The default value of 1280 is the maximum horizontal resolution of 

the Stencil 2 Feature Tracking camera. 

•

 

max_image_height:

 

The default value of 1024 is the maximum vertical resolution of the 

Stencil 2 Feature Tracking camera.

 

•

 

Video_conversion_speed_multiplier:

 1.0 – 

The image saver saves images and 

creates a movie file from them at the end of scanning. This parameter can be used to 
speed up the video frame rate as movies might be slow and monotonous in real time.

 

velodyneCloudReceiver

: 

•

 

logSensorPath

:

 true - Set to false to not record a sensor trajectory file while running 

localization. 

•

 

laserCloudSkipDis

:

 0.02 - Minimum distance in meters for Stencil to move between two 

scans to record new data. If 0, log every point. if < 0, do not create a pointcloud. If >= 0, log 
lidar points every laserCloudSkipDis meters 

Содержание STENCIL 2




















































































































































Отзывы:

Нет отзывов