JVC DR-MV1, Инструкция по эксплуатации

Страница: 81 / 104

Masterpage:Right+
EN
81
Filename [DR-MV1SE_10Subsidiary.fm]
Page 81 March 11, 2004 7:27 pm
SUBSIDIARY SETTINGS
8
DIRECT REC — OFF / ON
When this function is set to “ON”, you can easily start recording the
programme that you are watching on your TV. Press and hold
7
and press
4
on the remote control, or press
7
on the unit.
NOTES:
●
When you use the Direct Rec function, be sure to use a TV offering
T-V LINK, etc. and connect a fully-wired 21-pin SCART cable
between the unit and the TV. (
墌
pg. 16)
●
If “DIRECT REC” is set to “OFF”, the
7
button functions as described
in “Basic Recording” (
墌
pg. 52).
●
During Direct Rec, “– –” appears on the front display panel.
●
Even if there is no power supply for more than 60 minutes, the unit
keeps the setting.
8
POWER SAVE — OFF / ON
When this function is set to “ON”, you can reduce the power
consumption while the unit is turned off.
NOTES:
●
During Power Save mode —
— the front display panel will be turned off.
— the Just Clock function (
墌
pg. 85) does not work.
●
Power Save does not work when —
— the unit is in the Timer mode.
— the unit’s power is turned off after timer-recording or Instant Timer
Recording.
●
It takes some time for the unit to complete initialisation after you turn
on unit power, with “WAKE UP” blinking on the front display panel.
8
AUTO SP
]
EP TIMER — ON / OFF
When this function is set to “ON”, the unit automatically switches to
EP mode to allow complete recording if there is not enough tape to
record the entire programme while timer-recording in SP mode.
For Example:
Recording a programme of 140 minutes in length onto a 120-
minute tape
Make sure you set this function to “ON”, before the timer-recording
starts.
NOTES:
●
If you have programmed the unit to timer-record 2 or more
programmes, the second programme and those thereafter may not fit
on the tape if you set “AUTO SP
]
EP TIMER” to “ON”. In this case,
make sure the mode is not engaged, then set the tape speed
manually during timer programming.
●
In order to ensure that the recording fits on the tape, this feature may
leave a slight non-recorded section at the end of the tape.
●
There may be some noise and sound disturbance at the point on the
tape where the unit switches from SP to EP mode.
●
The Auto SP
]
EP Timer feature is not available during ITR (Instant
Timer Recording), and the feature will not work properly on the
following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120
8
VIDEO STABILIZER — ON / OFF
When this function is set to “ON”, you can automatically correct
vertical vibration in the picture when playing back unstable
recordings made on another recorder.
NOTES:
●
When you finish viewing a tape, be sure to set this function to “OFF”.
●
Regardless of the setting, this function has no effect during recording
and during special effects playback.
●
The on-screen display may jitter vertically when this function is set to
“ON”.
●
To watch recordings with close-caption, set this function to “OFF”.
8
L-2 SELECT — A/V / DECODER / SAT
Set “L-2 SELECT” to the appropriate mode depending on the type
of appliance connected to the unit’s L-2 IN/DECODER connector.
A/V
: To use this unit as the recording deck with the player
connected to the L-2 IN/DECODER connector, or to use the
satellite receiver connected to the L-2 IN/DECODER connector.
DECODER
: To use a decoder connected to the L-2 IN/DECODER
connector.
SAT
: To view a satellite programme with the TV set while the unit is
turned off. (
墌
pg. 76)
NOTES:
●
If you have a satellite receiver or a decoder connected to the L-2 IN/
DECODER connector, be sure to set “L-2 SELECT” back to the
appropriate mode after editing.
●
If you are not connecting a satellite receiver or a decoder to the L-2
IN/DECODER connector, leave “L-2 SELECT” set to “A/V”.
●
When “L-2 SELECT” is set to “SAT”, “SAT” appears on the TV screen
or front display panel instead of “L-2”.
8
COLOUR SYSTEM — PAL/NTSC / MESECAM
You can play back PAL, NTSC and MESECAM tapes, or record
PAL and SECAM* signals on this unit. Select the appropriate
colour system.
* SECAM signals will be recorded as MESECAM on this unit; MESECAM is
the designation for tapes with SECAM signals that have been recorded on
a MESECAM-compatible PAL video cassette recorder.
PAL/NTSC
: To record PAL signals, or play back a PAL or NTSC
tape.
MESECAM
: To record SECAM signals, or play back a MESECAM
tape.
NOTES:
About NTSC Playback
●
Some TVs shrink the picture vertically and place black bars at the top
and bottom of the TV screen. This is not a malfunction on the part of
either the unit or the TV.
●
The picture may roll up and down. This can be corrected using the V-
HOLD control found on some TVs. (This cannot be corrected if the
TV does not have a V-HOLD control.)
●
The counter and tape remaining time readings will be incorrect.
●
During search, still, or frame-by-frame playback, the picture will be
distorted, and there may be a loss of colour.
●
Depending on the type of TV, the top and bottom portions of
superimposed displays may be cut off during NTSC playback.
Total 140 minutes
Approximately 110 minutes Approximately 30 minutes
SP mode EP mode
DR-MV1SE_00.book Page 81 Thursday, March 11, 2004 7:28 PM