Masterpage:Right+
EN
77
Filename [DR-MV1SE_09Editing.fm]
Page 77
March 11, 2004 7:27 pm
SYSTEM CONNECTION
These instructions enable you to connect your unit to a Dolby
Digital decoder or an amplifier with built-in DTS.
1
Connect the unit and a Dolby Digital decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
●
For Dolby Digital sound, set “DIGITAL AUDIO OUT” to “DOLBY
DIGITAL/PCM”. (
墌
pg. 78)
●
For DTS sound, set “DIGITAL AUDIO OUT” to “STREAM/PCM”.
(
墌
pg. 78)
CAUTIONS:
●
This unit has a dynamic range of more than 110 dB with regards to its
Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to the
speakers may damage them.
●
Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do not
place the speakers adjacent to the TV set as this can adversely affect
the playback picture.
When you can’t switch the audio chaonnel of a bilingual
programme
When the unit is connected with a digital audio device using an
optional optical cable and “DIGITAL AUDIO OUT” is set to “DOLBY
DIGITAL/PCM”, it is not possible to switch the audio channel of a
bilingual programme recorded on a DVD-RAM or DVD-RW (VR
mode) disc. In this case, perform the following steps using the
remote control to switch “DIGITAL AUDIO OUT” from “DOLBY
DIGITAL/PCM” to “PCM ONLY”.
A
Press
SET UP
to access the Main Menu screen.
B
Press
w e
to select “DVD SET UP”, then press
ENTER
.
C
Press
w e
to select “AUDIO OUTPUT”, then press
ENTER
.
D
Press
rt
to select “DIGITAL AUDIO OUT”, then press
ENTER
.
E
Press
rt
to select “PCM ONLY”, then press
ENTER
.
(
墌
pg. 78)
F
Press
SET UP
to complete the setting.
G
Press
AUDIO
to select the desired audio channel. (
墌
pg. 28)
The L-2 IN/DECODER connector can be used as an input
connector for an external decoder (descrambler). Simply connect a
decoder and you can enjoy a variety of programming that is
available through scrambled channels.
1
Set “L-2 SELECT” to “DECODER”. (
墌
pg. 72)
2
Connect your unit’s L-2 IN/DECODER connector to the
decoder’s 21-pin SCART connector using a 21-pin SCART cable.
3
Perform the procedure as described in “When Receiving A
Scrambled Broadcast” (
墌
pg. 84).
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
2
Note for connection:
Remove the protection cap from the cable.
Coaxial cable
(not supplied)
Dolby Digital Decoder or
amplifier with built-in DTS
To DIGITAL AUDIO input
Optical cable
(not supplied)
DIGITAL AUDIO OUT (OPTICAL)
DIGITAL AUDIO OUT (COAXIAL)
Connecting/Using A Decoder
TV
RF cable
(provided)
TV aerial cable
L-1 IN/OUT
L-2 IN/DECODER
Decoder
DR-MV1SE_00.book Page 77 Thursday, March 11, 2004 7:28 PM
Содержание DR-MV1
Страница 101: ...EN 101 Memo ...
Страница 102: ...102 EN Memo ...
Страница 103: ...EN 103 Memo ...
Страница 104: ...DR MV1 COPYRIGHT 2004 VICTOR COMPANY OF JAPAN LTD E 104 EN EN Printed in Beijing 0304MNH ID BJ ...