JVC DR-MV1, Инструкция по эксплуатации

Страница: 44 / 104

Filename [DR-MV1SE_06DVD Operation2.fm]
Masterpage:Left+
44
EN
Page 44 March 11, 2004 7:27 pm
OPERATIONS ON DVD DECK
You can programme this unit to timer-record as many as
8 programmes.
If you do not know the S
HOW
V
IEW
number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
1
Load a recordable disc.
2
Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
3
Press PROG/CHECK to
access the ProgrammeCheck
screen.
●
When “PROGRAMME FULL
DELETE UNWANTED TIMER
PROGRAMME” appears on the
TV screen, you need to cancel
some of the reserved
programmes. (
墌
pg. 47)
4
Press
rt
to select “NEW
TIMER PROGRAMME”, then
press
ENTER . The programme
screen appears.
5
Press
rt
to set the desired
date.
●
The current date appears on the
TV screen. The date you enter
appears in its place.
6
Press
w e
to select “START”, then press
rt
to set the desired
start time.
●
Each press of
rt
advances/goes back the start time in 1-min.
increments.
●
To advance/go back the start time in 30-min. increments, press and
hold
rt
.
7
Press
w e
to select “STOP”, then press
rt
to set the desired
stop time.
●
Each press of
rt
advances/goes back the stop time in 1-min.
increments.
●
To advance/go back the stop time in 30-min. increments, press and
hold
rt
.
8
Press
w e
to select “TV PROG”, then press
rt
to select the
desired channel.
9
Set the other recording options as required.
●
Refer to step 6 in “S
HOW
V
IEW
® Timer Programming” (
墌
pg. 43).
10
Press ENTER to access the Programme Confirmation screen.
11
Press ENTER to complete timer programming.
●
To programme another timer, repeat steps 3 – 11 .
12
Press DVD TIMER (
#
) to engage the unit’s timer mode. The
DVD timer lamp lights up on the unit and the VCR deck is
automatically selected. When the VCR deck is in timer standby
mode, the unit is automatically turned off.
●
To disengage the timer mode, press DVD TIMER (
#
) again.
NOTES:
●
When two successive programmes are recorded on a DVD-RW disc
with Manual Timer programming function, the beginning of the
second one may be left off the recording.
●
If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme Delivery
Control) and VPS (Video Programme System) are services
designed to assure safe, accurate timer recording. With this
system, special code signals are transmitted together with the
audio/video signals. These code signals control your video unit and
have precedence over the advertised times you may have preset
into the timer. This means that your unit will start and stop
recording when the preset TV programmes actually start and end
— even if the broadcast time of a preset TV programme is
changed.
NOTES:
●
When you use Manual Timer Programming, set the start time (VPS
or PDC time) exactly as advertised in the TV listing. A different time
than advertised will result in no recording.
●
VPS/PDC recording is also possible when a satellite receiver or a
cable system is connected to L-2 IN/DECODER connector on your
unit.
●
VPS/PDC recording is also possible via the L-1 IN/OUT connector.
How to check if the station being received transmits a VPS/
PDC signal
A Hold down DISPLAY for about 5 seconds. “VPS/PDC” appears
blinking on the front display panel. If a VPS/PDC signal is detected
from the station, “VPS/PDC” will stop blinking. If no VPS/PDC
signal is detected from the station, “VPS/PDC” will blink at a slower
rate.
B
Press DISPLAY again to return to normal display.
Manual Timer Programming
●
Make sure that the unit’s built-in clock is set properly.
●
Turn on the unit.
●
Turn on the TV and select the AV mode.
●
Slide the TV/CABLE/SAT/DVD switch to DVD .
1
4
7
2
5
8
0
3
6
9
PROG/CHECK
7
ENTER
DVD TIMER (
#
)
rtw e
VCR/DVD
SAT
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
programming:
A
Perform “Satellite Receiver Control Setting” (
墌
pg. 21).
B
Perform “Manual Timer Programming” (
墌
pg. 44). In step 8 ,
press AUX to change “TV PROG” to “SAT”. Then press
rt
to
enter the channel position for the satellite broadcast. In step 9 ,
you cannot set “VPS/PDC” to “ON”.
C Leave the satellite receiver’s power on.
DR-MV1SE_00.book Page 44 Thursday, March 11, 2004 7:28 PM