JVC CA-MXDVA9 Скачать руководство пользователя страница 10

Страница: 10 / 73

MX-DVA9/MX-DVA9R

1-10

Prior to performing the following procedure, remove
the metal cover.

Disconnect the card wire from connector CN1 on the
tuner board on the right side of the body.

Remove the plastic rivet fixing the tuner board.

Remove the two screws F on the back of the body.

Removing the tuner board

(See Fig.13 and 14)

Prior to performing the following procedure, remove
the metal cover and the DVD changer mechanism
assembly, the tuner board.

Remove the screw G attaching the rear cover on the
back of the body.

Push each tab of the four joints b in the direction of
the arrow and release.

Remove the fourteen (A/B/EN) or sixteen(US/UJ/UG/
UN/UW) screws F attaching the rear panel.

Disengage the joints c on each lower side of the rear
panel using a screwdriver and remove the rear panel
backward.

Removing the rear cover / rear panel

(See Fig.15 to 17)

When reassembling, connect the earth
terminal which is extending from the
DVD changer mechanism assembly and
attached to the tuner board, to the inner
side of the rear panel.

CAUTION:

Fig.15-1

Rear panel

Fig.15-2

Rear panel

Fig.13

Fig.14

Fig.16

Fig.17

CN1

Plastic rivet

Tuner board

Rear panel

Joints b

Rear cover

Joint c

Rear panel

Содержание CA-MXDVA9










































































Результаты поиска

Содержание CA-MXDVA9

Отзывы:

Похожие инструкции для CA-MXDVA9

Бренды по названию

Популярные бренды

JVC CA-MXDVA9, Руководство по обслуживанию

Результаты поиска

Содержание CA-MXDVA9

Отзывы:

Похожие инструкции для CA-MXDVA9

Бренды по названию

Популярные бренды