JVC CA-MXDVA9 Скачать руководство пользователя страница 9

Страница: 9 / 73

MX-DVA9/MX-DVA9R

1-9

Prior to performing the following procedure, remove
the metal cover and DVD changer mechanism
assembly.

Disconnect the card wires from connector CN500,
CN505 and CN510 on the main board respectively.

Remove the wire clamp and disconnect the wire from
connector CN703 on the amplifier board.

Disconnect the wire from connector CN220 on the
transformer board.

Remove the plastic rivet attaching the main board to
the front assembly on the right side of the body.

Remove the two screws E on the bottom of the
body.

Release the two joints a on the lower right and left
sides of the body using a screwdriver, and remove
the front panel assembly toward the front.

Removing the front panel assembly

(See Fig.8 to 12)

Fig.8

Fig.9

Wire clamp

Power amplifier board (2)

CN703

Main board

CN500

CN505

CN510

Transformer board

CN220

Front panel
assembly

Plastic rivet

Front panel assembly

Main board

Fig.10

Fig.11

Fig.12

Front panel assembly

Joint a

Front panel assembly

(Bottom)

Содержание CA-MXDVA9










































































Результаты поиска

Содержание CA-MXDVA9

Отзывы:

Похожие инструкции для CA-MXDVA9

Бренды по названию

Популярные бренды

JVC CA-MXDVA9, Руководство по обслуживанию

Результаты поиска

Содержание CA-MXDVA9

Отзывы:

Похожие инструкции для CA-MXDVA9

Бренды по названию

Популярные бренды