JVC CA-MXDVA9 Скачать руководство пользователя страница 11

Страница: 11 / 73

MX-DVA9/MX-DVA9R

1-11

Prior to performing the following procedure, remove
the metal cover, the DVD changer mechanism
assembly, the rear panel and the antenna board.

Disconnect the card wire from connector CN500,
CN505, CN510 and the wire from CN513 on the
main board respectively.

Remove the plastic rivet and the screw H attaching
the main board on the right side of the body.

Disconnect connector CN521 on the main board
from the analog output board outward. Disconnect
connector CN530 and CN531 in the lower part of the
main board from the regulator board upward.

Removing the main board

(See Fig.18 and 19)

Prior to performing the following procedure, remove
the metal cover, the DVD changer mechanism
assembly and the rear panel.

Disconnect connector CN287 on the speaker board
from the regulator board.

Removing the speaker board

(See Fig.20)

It is not necessary to remove the main
board.

REFERENCE:

Fig.18

Fig.19

Fig.20

Front panel assembly

Main board

CN513

CN505

CN510

Plastic rivet

Main board

CN521

CN531

Regulator board

CN287

Speaker board

CN500

Analog output board

CN520

Analog output board

CN530

Содержание CA-MXDVA9










































































Результаты поиска

Содержание CA-MXDVA9

Отзывы:

Похожие инструкции для CA-MXDVA9

Бренды по названию

Популярные бренды

JVC CA-MXDVA9, Руководство по обслуживанию

Результаты поиска

Содержание CA-MXDVA9

Отзывы:

Похожие инструкции для CA-MXDVA9

Бренды по названию

Популярные бренды