JVC CA-MXDVA9 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 73

background image

MX-DVA9/MX-DVA9R

1-13

Prior to performing the following procedure, remove
the metal cover, the DVD changer mechanism
assembly, the rear panel, the antenna board and the
analog output board.

Disconnect the wire from connector CN513 on the
main board.

Remove the wire clamp on the power amplifier board
(1).

Disconnect the wire from connector CN703 on the
power amplifier board (2).

Disconnect connector CN310 on the power amplifier
board (1) and CN701 on the power amplifier board
(2) from the regulator board upward. The heat sink is
detached with the power amplifier board (1) and the
power amplifier board (2).

Remove the four screws J attaching the power
amplifier board (1) to the heat sink.

Remove the four screws K attaching the power
amplifier board (2) to the heat sink.

1.

2.

3.

4.

5.

6.

Removing the power amplifier board (1)
/ power amplifier board (2) / heat sink

(See Fig.25 to 27)

Fig.25

Fig.26

Fig.27

Wire clamp

Power amplifier

board (1)

CN310

Regulator board

CN701

Heat sink

Power amplifier

board (2)

Main board

CN513

CN703

Heat sink

Power amplifier board (1)

Power amplifier board (2)

J

J

Power amplifier board (1)

Power amplifier board (2)

Heat sink

K

K

«
...
11
12
13
14
15
...
»

Содержание CA-MXDVA9










































































Отзывы:

Нет отзывов

Похожие инструкции для CA-MXDVA9

Бренд: M86 Security Страницы: 86

Бренд: JBL Страницы: 6

Бренд: iHome Страницы: 12

Бренд: iHome Страницы: 2

Бренд: Nelson Страницы: 18

Бренд: Nelson Страницы: 150

Water Jet Lightning

Бренд: Oase Страницы: 28

Бренд: Oase Страницы: 9

Бренд: Montarbo Страницы: 23

Бренд: Vacron Страницы: 2

HQ Power VDSABS15A

Бренд: Velleman Страницы: 13

ESX SIGNUM Series

Бренд: Audio Design Страницы: 4

SECURITY SYSTEM

Бренд: HAI Страницы: 82

JBL JBLPARTYBOXGOBRU

Бренд: Harman Страницы: 17

ZH-T202SF Series

Бренд: Zenith Страницы: 57

Бренд: Kompernass Страницы: 40

AcousticDesign AD-C4T-WH

Бренд: QSC Страницы: 4

Бренд: iStorage Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды