JVC CA-MXDVA9 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 73

background image

MX-DVA9/MX-DVA9R

1-14

Prior to performing the following procedure, remove
the metal cover, the DVD changer mechanism
assembly and the rear panel.

Disconnect the wire from connector CN218 and
CN219(only US/UJ/UG/UN/UW) on the power board.

Remove the two wire clamps on the power amplifier
board (1) and power board.

Disconnect the wire from connector CN204 on the
regulator board.

Disconnect the wire from connector CN220 on the
transformer board.

Remove the four screws L attaching the power
transformer assembly.

1.

2.

3.

4.

5.

Removing the power transformer assembly
(See Fig.28 and 29)

Prior to performing the following procedure, remove
the metal cover, the DVD changer mechanism
assembly, the rear panel, the antenna board, the
main board, the analog output board, the power
board, the power amplifier board (1), the power
amplifier board (2) and the speaker board.

Disconnect the wire from connector CN204 on the
regulator board.

Remove the two screws M.

1.

2.

Removing the regulator board

(See Fig.30)

Fig.28

Fig.29

Fig.30

Wire clamps

Transformer board

CN220

M

M

Regulator board

CN204

Power transformer assembly

Power board

CN218

Regulator board

CN204

Power transformer assembly

L

L

L

L

L

CN220

Power transformer assembly

Wire clamp

Regulator board

CN204

CN219

«
...
12
13
14
15
16
...
»

Содержание CA-MXDVA9










































































Отзывы:

Нет отзывов

Похожие инструкции для CA-MXDVA9

Бренд: LaCie Страницы: 13

Бренд: Cambridge SoundWorks Страницы: 20

Бренд: Dali Страницы: 8

Бренд: Dali Страницы: 42

Бренд: Dali Страницы: 34

Бренд: Dali Страницы: 2

Бренд: Dali Страницы: 37

Бренд: Dali Страницы: 2

Бренд: Dali Страницы: 15

Бренд: TAC Страницы: 20

Бренд: Fanvil Страницы: 6

Бренд: Gato Audio Страницы: 12

Бренд: Neat Страницы: 30

Бренд: ZKTeco Страницы: 16

Бренд: Tannoy Страницы: 4

Бренд: Nady Audio Страницы: 2

ACTIVE REFLEX 300A II Series

Бренд: Magnat Audio Страницы: 28

Бренд: Roland Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды