background image

Resolved Known Problems

„

53

Release 10.2.2

Forwarding

„

LM10A or LM10+ crashes when removing merge policies; file: 
aptationLayer.cc; line: 7515; task: scheduler. [Defect ID 185102]

„

Packets with router alert IP option configured are sent to SRP though the source 
addresses in the packets are not local and the associated protocol is disabled. 
[Defect ID 88859]

„

Unable to send message type X to address (15a15 0) because ICC returned 
error code Y log message not clear. [Defect ID 89524]

„

LM10 Memory leak due to PPP or DHCP subscriber flap. [Defect ID 90570]

Hardware

„

Gigabit Ethernet interface in failed state where link is down but interface is up. 
[Defect ID 89942]

„

Serial number for fan in 

show hardware

 command output is not updated when 

fan is swapped. [Defect ID 90008]

IGMP

„

The output of the 

show ip traffic

 command erroneously displays IGMP packets 

on ES2 10G LM, as multicast packets. [Defect ID 90041]

IP

„

Executing BFD 

last-resort

 also enables RTR

 last-resort

. [Defect ID 89510]

„

Although the IP access-internal route is deleted from the routing table after you 
issue the 

shutdown 

command on a major PPP interface, or after you issue the 

logout subscribers all

 command and the subscribers try to log in again, 

logging in of PPP subscribers fails. This problem occurs because the AAA server 
that authenticates subscribers responds with a message that access is denied 
owing to detection of duplicate addresses. Also, the 

access denied: duplicate 

address detected

 message is recorded in the aaaUserAccess event log category 

that you can view from the output of the 

show log

 command. [Defect ID 

185109]

L2TP

„

SRP reset type: processor exception 0x68616c74 (halt) task: ip_Ctrl_2 with 
continuous SNMP polling. [Defect ID 90472]

MPLS

„

LDP and OSPF flap when an unconfigured LM10 is reloaded with 75k MPLS 
next hops. [Defect ID 90471]

Содержание JUNOSe 10.2.2























































































































Отзывы: