Juniper JUNOSe 10.2.2 Скачать руководство пользователя страница 23

Страница: 23 / 118

Known Behavior

Release 10.2.2

hostname

Domain Map Tunnel
Configuration

Still available in Global
Configuration mode

client-name

hssi description

Interface Configuration

hssi force dte acknowledge

Interface Configuration

hssi internal-clock

Interface Configuration

ignore dcd

Interface Configuration

ignore link-state-signals

Interface Configuration

[ no ] ike cr

Global Configuration

[ no ] ipsec crl

interface hssi

Global Configuration

invert tx clock

Global Configuration

ip dhcp-local cable-modem

Global Configuration

set dhcp-relay with the
strings docsis and pktc in
the server-string mapping
specification

ip mirror

Global Configuration

ip policy secure-input and
ip policy secure-output; for
E120 and E320 routers, you
must use these commands
because the ip mirror
command has been
removed from the CLI for
those routers.

ip policy local-input

Interface Configuration,
Profile Configuration

None

[ no ] ipsec isakmp-policy rule

Global Configuration

[ no ] ipsec ike-policy-rule

ipv6 policy local-input

Interface Configuration,
Profile Configuration

None

Controller Configuration

license l2tp-session

Global Configuration

None

lineCoding

Controller Configuration

log

Policy List Configuration

log severity debug
dhcpLocalProtocolDecode

Global Configuration

log severity debug
dhcpCapture

loopback

Domain Map Configuration

Still available in Controller
Configuration and Interface
Configuration modes

local-interface

loopback remote { remote line fdl
ansi | remote line fdl bellcore |
remote line inband remote payload
[ fdl ] [ ansi ] }

Controller Configuration

mark

Policy List Configuration

mark in Classifier Group
Configuration mode

Deprecated Command

Command Mode

Preferred Command

Содержание JUNOSe 10.2.2























































































































Результаты поиска

Содержание JUNOSe 10.2.2

Отзывы:

Похожие инструкции для JUNOSe 10.2.2

Бренды по названию

Популярные бренды

Juniper JUNOSe 10.2.2, Руководство по выпуску

Результаты поиска

Содержание JUNOSe 10.2.2

Отзывы:

Похожие инструкции для JUNOSe 10.2.2

Бренды по названию

Популярные бренды