JUKI APW-896N/IP-420 Скачать руководство пользователя страница 86

Страница: 86 / 142

− 82 −

③

Register the sewing data to SEWING DATA CUSTOMIZING

button

Up to 4 sewing data can be registered to SEWING DATA CUS-
TOMIZE buttons

When pressing CUSTOMIZING button

you desire to register,

the sewing data list (screen A) is displayed.

④

Select the sewing data to be registered

Select the sewing data you desire to register with SEWING DATA

button

When the selected button is pressed twice, the selection is re

leased.

The data below have been registered in order from the left at the time of your purchase.

Sewing data list screen

(Screen A)

⑤

Register the data to the customizing button

When ENTER button

is pressed, register to the cus

tomizing button ends, and the screen returns to the customizing

screen of the input screen. The registered sewing data is dis-
played on CUSTOMIZING button

Lockstitch pitchy

Condensation/back tack at sewing start selection

Condensation/back tack at sewing end selection

Dart stretcher stop/motion change-over

Содержание APW-896N/IP-420















































































































































Результаты поиска

Содержание APW-896N/IP-420

Отзывы:

JUKI APW-896N/IP-420, Инструкция по эксплуатации, Страница: 86 / 142

Результаты поиска

Содержание APW-896N/IP-420

Отзывы: