JUKI APW-896N/IP-420 Скачать руководство пользователя страница 118

Страница: 118 / 142

− 114 −

②

Display the corner knife adjustment sewing screen.

When pressing the pattern button you desire to adjust, the corner
knife adjustment sewing screen (A) is displayed.

Input screen

Corner knife adjustment sewing

screen (A)

Corner knife adjustment sewing

screen (B)

When performing the adjustment of corner knife using this mode at the time of replacement of
corner knife, be sure to confirm again the compensation value of each data of the corner knife.

When MODE CHANGEOVER key

is pressed, the input

screen is displayed.

When READY key

is pressed, the corner knife adjustment

sewing screen (B) is displayed.

Press PATTERN SELECTION button

for corner knife

adjustment and the screen returns to the pattern selection screen
for corner knife adjustment.

Содержание APW-896N/IP-420















































































































































Результаты поиска

Содержание APW-896N/IP-420

Отзывы:

JUKI APW-896N/IP-420, Инструкция по эксплуатации, Страница: 118 / 142

Результаты поиска

Содержание APW-896N/IP-420

Отзывы: