manualshive.com logo in svg

JUKI APW-896N/IP-420, Инструкция по эксплуатации, Страница: 107 / 142

Поделиться
Скачать
JUKI APW-896N/IP-420 Скачать руководство пользователя страница 107

− 103 −

3. REPLENISHING GREASE TO THE DESIGNATED PLACE

* When “Grease-up warning E220” or “Grease-up error E221” is displayed, or when the machine has been 

used for one year, be sure to perform replenishing of grease.

When turning ON the power after the sewing machine has operated up to 40 million stitches, “grease-up 
warning E220” informing of the time of grease replenishment is displayed on the panel. When pressing RE-

SET button 

 to leave the error screen, the machine can continue operating. However, the error has not 

been released and the error is displayed every time the power is turned ON. After performing replenishment 
of grease which is explained later, call “Memory switch

 

 

” and set the number of stitches of operation to 

“0” with CLEAR button 

 .

When the machine has been continuously used up to 48 million stitches, “grease-up error E221” is displayed 
on the panel. In this case, even when RESET button 

 is pressed and the error screen is released, the 

sewing after that cannot be performed. Be sure to call “Memory switch

 

 

” and set the number of stitch-

es of to “0” with CLEAR button 

 after performing replenishment of grease which is explained later.

 

1.  “Grease-up warning E220” and “Grease-up error E221” are displayed again unless memory 

switch 

 is cleared to “0” after replenishing grease.

 

2.  Be sure to use the grease tube (Part No. : 40006323) supplied with the machine as accessories 

for replenishing grease to the designated place which is explained later. If any grease other than 
the designated one is replenished, Component breakage will be caused.

 

3.  Keep the used grease tube in a safe place.

CAUTION 

: 

To prevent accidents caused by abrupt start of the sewing machine, start the work after turning OFF 

the power.

①

  Loosen two screws 

❶

 (SM6040602TP) and 

move wiper cylinder 

❷

 to the right side.

❶

❷

Содержание APW-896N/IP-420















































































































































Отзывы:

Нет отзывов