JUKI APW-896N/IP-420 Скачать руководство пользователя страница 132

Страница: 132 / 142

− 128 −

Error code

Description of error

How to recover

A203

Oil replacement time warning

When operation time of the sewing machine is reached to the oil
replacement time that is set from the panel.

Possible to re-
start after reset.

E220

Grease-up warning

When number of stitches of operation is reached to 40 million

stitches.

Possible to re-
start after reset.

E221

Grease-up error

When number of stitches of operation is reached to 48 million

stitches, a sewing impossible state occurs.

* After applying grease, it is possible to release when clearing

memory switch

Number of stitches of grease-up.

Possible to re-
start after reset.

E303

Semilunar plate sensor error

Detection of upper dead point of the sewing machine cannot be
performed.

Turn OFF the
power.

E349

Step-out detection sensor does not react.

For the emergency procedure, it is possible to continually use by
re-starting with the reset button.

However, check the sensor and be sure to replace it when it is

defective.

Possible to re-
start after reset.

E351

Reflecting tape for detecting angle has been deteriorated.

Possible to re-
start after reset.

E353

Angle detection sensor fails to detect.

* Clean dust on the reflecting tape of the flap base with an air gun.

Possible to re-
start after reset.

E354

Angle detection sensor forced stop

Possible to re-
start after reset.

E355

Angle detection sensor dust detection

* Clean dust on the reflecting tape of the flap base with an air gun.

Possible to re-
start after reset.

E356

Angle detection sensor front end fails to detect.

Possible to re-
start after reset.

E357

Corner knife on the moving side, left is held lifted.

Possible to re-
start after reset.

Содержание APW-896N/IP-420















































































































































Результаты поиска

Содержание APW-896N/IP-420

Отзывы:

JUKI APW-896N/IP-420, Инструкция по эксплуатации, Страница: 132 / 142

Результаты поиска

Содержание APW-896N/IP-420

Отзывы: