JUKI APW-896N/IP-420 Скачать руководство пользователя страница 61

Страница: 61 / 142

− 57 −

②

Items that are displayed in the sewing data list screen

No.

Item

Setting range

Edit unit

Initial value

Flap priority sewing selection

Flap priority sewing mode is selected.
* It is possible to set only when alternate sewing mode is set.

- - -

※

Flap priority sewing pro-

hibited

Flap priority sewing

mode

Selection of automatic changeover of marking light irradiation position

When

is sewing start irradiation or sewing end irradiation, the marking

irradiation position is automatically changed over after end of sewing.
* This function does not move at the time of alternate sewing mode and

cycle sewing mode.

- - -

※

Stop

Motion

Flap forced stop data

When flap sewing end is not detected, the machine stops after sewing as
long as the set length from rear reference position.
* It is possible to set only when

is set to flap sewing.

0.0 to 10.0

0.1mm

5.0mm

※

Compensation value of deflection detection at the start of sewing

Further compensation is performed to the deflection automatically detected
at the start of sewing.

–9.9 to
9.9mm

0.1mm

0.0mm

Compensation value of deflection detection at the end of sewing

Further compensation is performed to the deflection automatically detected
at the end of sewing.

–9.9 to
9.9mm

0.1mm

0.0mm

Lockstitch pitch

Sewing pitch of lockstitch section is set.

2.0 to 3.4

0.1mm

2.5mm

Selection of condensation/back tack at sewing start

Condensation/back tack at sewing start is selected.

- - -

Condensation

Back tack

Number of condensation stitches at sewing start

Number of condensation stitches at sewing start is set.

It is possible to set only when

is set to selection of condensation.

3 to 19

1 stitch

5 stitches

※

. . . Item that is not displayed due to other setting state

Содержание APW-896N/IP-420















































































































































Результаты поиска

Содержание APW-896N/IP-420

Отзывы:

JUKI APW-896N/IP-420, Инструкция по эксплуатации, Страница: 61 / 142

Результаты поиска

Содержание APW-896N/IP-420

Отзывы: