Jøtul GI 545 DV MV Скачать руководство пользователя

Страница: 2 / 36

139919_GI 545 DV and DV MV 5/19

PLEASE NOTE:

Initial Break-in

It is normal for smoke and odor to occur during the initial

stages of operation, depending upon temperatures

generated over time. This curing condition can be

alleviated by promoting fresh air circulation within the

immediate vicinity of the appliance.

Operational Sounds

Please be aware that cast iron and steel components

expand and contract with temperature fluctuations

that are often accompanied by

“creaking” or “pinging” sounds.

This is the result of natural

thermal activity.

The optional blower fan will

also generate a slight hum at the

low setting and progressively

increase with the velocity of

forced air.

THIS OWNER’S MANUAL PROVIDES INFORMATION TO

ENSURE SAFE INSTALLATION AND EFFICIENT, DEPENDABLE

OPERATION OF YOUR FIREPLACE INSERT. PLEASE READ

THESE INSTRUCTIONS IN THEIR ENTIRETY AND MAKE THEM

AVAILABLE TO ANYONE USING OR SERVICING THIS GAS

INSERT.
DO NOT ATTEMPT TO ALTER OR MODIFY THE CONSTRUCTION

OF THIS APPLIANCE OR ITS COMPONENTS. ANY

MODIFICATION OR ALTERATION WILL VOID THE WARRANTY,

CERTIFICATION AND LISTING OF THIS APPLIANCE.
THIS HEATER MUST BE INSTALLED AND MAINTAINED BY A

QUALIFIED SERVICE AGENCY.

Suggested Tools for Installation and Service

• External regulator (for Propane only)

• Piping that complies with local code

• A manual shut-off valve is included with this appliance,

however, an additional T-Handle valve may be required in

Massachusetts

• Sediment trap

- if required by code

• Tee joint

• Pipe wrench

• Pipe sealant

• 10 mm open end wrench

• 1/2” & 7/16” open end wrench

• Phillips head screwdriver

• Flat head screwdriver

• 1/4” nut driver

• Work Gloves

• Safety glasses

• Torx T-20 screwdriver

• Tin snips

• Glass Frame Latch Tool

- included with appliance.

Retain and store as shown in fig. 7.3.

Installation Requirements for the

Commonwealth of Massachusetts

THIS PRODUCT MUST BE INSTALLED BY

A LICENSED MASTER OR JOURNEYMAN

PLUMBER OR GAS-FITTER WHEN

INSTALLED IN THE COMMONWEALTH OF

MASSACHUSETTS.

1. If there is not one already present,

on each floor level where there are

bedroom(s), a carbon monoxide detector

and alarm shall be placed in the living

area outside the bedroom(s). The carbon

monoxide detector shall comply with

NFPA 720 (2005 Edition).

2. A carbon monoxide detector shall:

a) Be located in the room that houses

the appliance or equipment;

b) Be either hard-wired or battery

powered or both; and

c) Shall comply with NFPA 720 (2002

Edition).

3. A Product-approved vent terminal must

be used, and if applicable, a Product-

approved air intake must be used.

Installation shall be in strict compliance

with the manufacturer’s instructions. A

copy of the installation instructions must

remain with the appliance or equipment

at the completion of the installation.

63.28%

Natural Gas

Jøtul GI 545 DV MV

65.39%

Propane

Based on CSA P.4.1-15

61.37%

Natural Gas

Jøtul GI 545 DV

64.26%

Propane

Based on CSA P.4.1-15

Содержание GI 545 DV MV





































Результаты поиска

Содержание GI 545 DV MV

Отзывы:

Похожие инструкции для GI 545 DV MV

Бренды по названию

Популярные бренды

Jøtul GI 545 DV MV, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GI 545 DV MV

Отзывы:

Похожие инструкции для GI 545 DV MV

Бренды по названию

Популярные бренды