background image

15

139919  GI 545 DV and DV MV  5/19

 

REQUIRED INLET GAS PRESSURES

  

(inches water column)

   

  MIN 

  MAX 

NATURAL GAS 

5.0  WC 

7.0 WC 

PROPANE 

11.0 WC 

14.0 WC

REQUIRED MANIFOLD PRESSURES

(inches water column)

  

 MIN                  MAX 

NATURAL GAS 

1.1 WC 

3.8 WC 

PROPANE 

2.9 WC 

11.0 WC

ALWAYS TEST PRESSURE WITH THE VALVE REGULATOR 

ADJUSTED TO THE HIGHEST SETTING.

WARNING

DO NOT ALLOW THE INLET GAS PRESSURE TO 

EXCEED 

14.0

” WC (OR 1/2 PSIG) AS SERIOUS 

VALVE DAMAGE MAY RESULT.

Symptoms of incorrect gas pressure include:
Insufficient gas pressure:  

•  Small pilot flame which can result in poor pilot 

rectification and/or frequent burner outages.

•  Little variation in flame picture between HI and 

LO regulator settings.

•  Insufficient gas to support more than one 

appliance causing nuisance outages or gas 

surges.

Excessive gas pressure:

•  Permanent damage to valve causing complete 

appliance shut down.

•  Too large a pilot flame resulting in overheating 

of the flame sensor and consequent shut down.

•  Sooting due to impingement and/or incorrect 

fuel to air mix.

Figure 7.2.  Valve pressure test points and pilot adjustment.

B

A

Pilot Adjustment Screw

Regulator Control Knob

Содержание GI 545 DV MV





































Отзывы: