manualshive.com logo in svg

Jøtul GI 545 DV MV, Инструкция по установке и эксплуатации

Поделиться
Скачать
Jøtul GI 545 DV MV Скачать руководство пользователя страница 10

10

139919_GI 545  DV and DV MV  5/19

GAS VENT RULE

Flat to 6/12 

1’0”       0.3 m 

Over  7/12 to 9/12 

2’0”      0.6 m 

Over 10/12 to 12/12 

4’0”      1.2 m 

Over 13/12 to 16/12 

6’0”      1.8 m 

Over 17/12 to 21/12  

8’0”      2.4 m

 

ROOF SLOPE

Vent Installation Procedure

This appliance must be vented through the chimney by a 

pair of 3 inch flexible aluminum liners listed for use with 

gas appliances.  One duct is attached to the exhaust port 

on the top of the unit and will carry the exhaust gases to 

the outside of the house. This exhaust liner must run the 

full length of the chimney and be directly connected to the 

chimney termination cap.  See figures 6.1 - 6.2.

The other 3 inch liner will be attached to the air intake 

port and will provide fresh air for combustion to the unit.  

This liner must extend through the damper area of the 

fireplace and at least into the first tile liner of the chimney. 

(U.S. ONLY).  This liner can also extend the full length of the 

chimney and connect to the termination cap.  

SEE NOTICES 

BELOW. 

See also figures 6.1-6.2.

         

        

 NOTICE

If the intake flex does not extend the full length 

of the chimney and connect to the unit and the 

termination cap -  

A NONCOMBUSTIBLE BLOCK OFF 

PLATE MUST BE CONSTRUCTED AND INSTALLED ABOVE 

THE UNIT BELOW THE END OF THE INTAKE DUCT

 

(normally at the damper area).  See figure 6.1.

To avoid cross venting the insert, label the duct to 

be used for the exhaust conduit at both the top and 

bottom ends. This ensures that the exhaust duct will 

be attached to the correct collar on the insert and on 

the chimney termination kit.

CANADA NOTE:  Both Intake and Exhaust ducts 

must extend the full length of the chimney and be 

connected to both the unit and the termination kit.

         

        

 NOTICE

THE USE OF AN EXISTING CHIMNEY AS AN AIR 

INTAKE IS NOT COVERED UNDER THE ANSI Z21.88-

2014-CSA 2.33-M04 TEST METHODS AND RESULTING 

ITS/WHI PRODUCT CERTIFICATION.  THE CODE 

AUTHORITY HAVING JURISDICTION MUST BE 

CONSULTED PRIOR TO PROCEEDING WITH THIS 

INSTALLATION METHOD.

6.0  Vent Guidelines

•  All vent components must be installed in accordance 

with the terms of their listing and manufacturer’s 

instructions.  See the Appendix on page 32 for a 

listing of approved vent manufacturers.

•  The minimum height of termination cap from the 

top of the unit shall be no less than 10 ft.(3.05 m), 

and the maximum height shall be no more than 35 ft.  

(10.67 m). See figures 6.1 - 6.2.

•  Steep roofs, nearby trees, or predominantly windy 

conditions can promote weak draft or occasional 

downdrafts. In such cases, increasing the height of 

the vent or installation of high wind termination 

caps may alleviate the condition.

•  HORIZONTAL RUNS are not permitted anywhere in 

the venting system.  

•  Vent liners may be no less than 3 inches diameter nor 

greater than 3 inches diameter 

with the following 

exception: 

PROPANE NOTICE: For LP installations with vent runs 

greater than 10’, it is recommended that a 4” exhaust 

liner be used to ensure best operating performance. 

This is especially appropriate for installations in 

warmer climates and intended for extended run 

times. Vent pipe adapters (3” to 4”) are available 

from Jotul-approved venting manufacturers. When a 

4” Exhaust liner is used, it is recommended that a 3” 

Intake liner be run all the way to the vent terminus.

•  Any unused flue or masonry enclosure can be used as 

a passageway for venting provided  the flue is relined 

using 3” or 4” Listed Flexible Gas Liner. The remaining 

space around the liner in a masonry or factory-built 

flue CANNOT be used to vent any other appliance.

•  Listed Flexible Gas Liners may not be exposed to any 

living space. 

•   Installation of any components not manufactured 

or approved by Jøtul or failure to meet all clearance 

requirements will void all warranties and could result 

in property damage, bodily injury, or loss of life.

•  Never modify any venting component, or use any 

damaged venting product.

Minimum Height 

From Roof

•  THE GAS APPLIANCE AND VENT SYSTEM MUST BE 

VENTED DIRECTLY TO THE OUTSIDE OF THE BUILDING, 

AND NEVER ATTACHED TO A CHIMNEY SERVING A SOLID 

FUEL OR GAS BURNING APPLIANCE. 

•  The minimum vent height above the roof or adjacent 

walls is specified by building codes. A general guide to 

follow is the Gas Vent Rule below.

Содержание GI 545 DV MV





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды