Jonsered FR 2113 MA 4X4 страница 42 Скачать руководство пользователя | Manualshive

Страница: 42 / 56

background image

40

– English

8009-273

6008-240H

6008-232

LUBRICATION

Checking the oil level in the transmission
on FR 2113, FR 2116

1. Remove the transmission cover. Loosen both

screws (one on each side) and lift off the
transmission cover.

2. Check that there is oil in the transmission’s oil

tank. Fill if necessary with engine oil
SAE 10W/30 (class SF-CC).

Lubricating the belt adjuster

The belt adjuster should be lubricated regularly
using good quality molybdenum disulphide grease*.
1 nipple from the right-hand side under the engine’s
lower belt pulley, until grease is forced out.

With daily use, lubrication should be carried out
twice weekly.

General lubrication

All joints and bearings are lubricated using
molybdenum disulphide grease during manu-
facture. Continue to lubricate using the same type
of grease *. Lubricate the steering and control wires
using engine oil.

Carry out this lubrication regularly; with daily use,
the machine should be lubricated twice weekly.

* Grease from well-known brand names (petrol
companies, etc.) usually maintains a good quality.
The most important property is that the grease
provides good protection against corrosion.

«
...
40
41
42
43
44
...
»

Содержание FR 2113 MA 4X4

























































Отзывы:

Нет отзывов

Похожие инструкции для FR 2113 MA 4X4

Бренд: Yard Machines Страницы: 20

Бренд: Poulan Pro Страницы: 44

Бренд: Yazoo Страницы: 9

G - PLEX WD series

Бренд: Ransomes Страницы: 181

Бренд: SaMASZ Страницы: 36

Бренд: COMPANION Страницы: 76

Бренд: MTD Страницы: 37

CYCLONE MJ31-200

Бренд: Major Страницы: 88

Бренд: Qualcast Страницы: 15

Бренд: LAWN STAR Страницы: 7

Бренд: MTD Страницы: 20

Бренд: AL-KO Страницы: 116

Бренд: Hayter Страницы: 26

Бренд: Flymo Страницы: 2

Бренд: Bushranger Страницы: 24

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды