Johnson JET 6000 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 62

background image

All or some of the keys on console do not work

Possible causes:

1.

Keypad connecting
plug is not fit-in
properly.

2.

Keypad is damaged.

3.

PCB is damaged.

Fix:

1.

Disconnect the keypad and replace the keypad,
and check again.

2.

Replace the keypad.

3.

Replace the PCB.

6-4 Revision: 1.0 Date: 2001-06-01

«
...
29
30
31
32
33
...
»

Содержание JET 6000































































Отзывы:

Нет отзывов

Похожие инструкции для JET 6000

Бренд: Smooth Fitness Страницы: 30

Бренд: LA Fitness Страницы: 12

Бренд: Pro-Form Страницы: 32

Pro-Form 1280 PREMIER ES

Бренд: ICON Страницы: 32

Бренд: ProForm Страницы: 8

Бренд: Yowza Страницы: 44

Бренд: NordicTrack Страницы: 42

Бренд: Ogawa Страницы: 51

Бренд: Life Fitness Страницы: 57

Бренд: Dyaco Страницы: 33

Бренд: Life Fitness Страницы: 3

Бренд: Ironman Fitness Страницы: 44

Бренд: Taurus Страницы: 64

Бренд: Walkdesk Страницы: 17

NordicTrack C990

Бренд: ICON Health & Fitness Страницы: 48

toorx EXPERIENCE

Бренд: Garlando Страницы: 19

Бренд: ICON Health & Fitness Страницы: 10

Бренд: Pro-Form Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды