Johnson JET 6000 Скачать руководство пользователя страница 7

Страница: 7 / 62

DECK RE-WAXING PROCEDURE

Frequency:

Every 1 month.

WAX
Name:

CHRIS TIAN

Content:

SUNWAYLUBE

1180

Viscosity Grade

Viscosity @40C

68.0

@100C

9 . 1

Viscosity Index

100

Pour Point, C

Flash Point, C

216

Procedure:

After removing the running belt, clean the deck and
belt by using a clean towel.

Place the (new) running belt.

Place some wax on the deck about 10 cm from the edge,
in such that the wax is evenly distributed across the
deck.

Tighten the deck screws and assemble the rear roller
first, then assemble the front roller.

Replace the drive belt on the transmission pulley by
turning the Flywheel clockwise by using left hand and
use right hand to push the drive belt on to grooves of
the front roller pulley.

Install the front / rear rollers. Adjust the roller fixed
bolts to center the running belt at speed 4mph (6.4kph).

Turn on the power and then press the start key, then
hold down the fast key until the window indicates

mph (3 kph) and then step on the belt for 5 minutes

to ensure the wax has been evenly distributed
underneath the belt.

1-3 Revision: 1.0 Date: 2001-06-01

Содержание JET 6000































































Результаты поиска

Содержание JET 6000

Отзывы:

Похожие инструкции для JET 6000

Бренды по названию

Популярные бренды

Johnson JET 6000, Руководство по обслуживанию

Результаты поиска

Содержание JET 6000

Отзывы:

Похожие инструкции для JET 6000

Бренды по названию

Популярные бренды