Johnson JET 6000 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 62

background image

CONSOLE CABLE REPLACEMENT

(JET-7000 series)

Tools required:

ü

Philips

screwdriver

ü

T-handle key
(5mm).

Procedure:

1.

Remove screws from

the front cover by using
the screwdriver and
remove it.

2.

Use the T-handle key

(5mm) to remove screws

of the left handle bar and
remove it.

3.

With the screwdriver

remove the screws from
the console base plate.

4.

Disconnect the console

cable from the PCB and

MCB.

5.

Use the T-handle key

(5mm) to remove the
screws holding the console
base to the stanchion and
remove the console base.

7-7 Revision: 1.0 Date: 2001-06-01

«
...
48
49
50
51
52
...
»

Содержание JET 6000































































Отзывы:

Нет отзывов

Похожие инструкции для JET 6000

Trainer PFTL39507.1

Бренд: ProForm Страницы: 28

Бренд: ProForm Страницы: 20

Бренд: ProForm Страницы: 26

600 S Treadmill

Бренд: ProForm Страницы: 26

6.0 GSX PFTL51105.3

Бренд: ProForm Страницы: 26

Бренд: ProForm Страницы: 30

Бренд: HOMCOM Страницы: 11

Бренд: Orbit Страницы: 27

Бренд: Shua Страницы: 29

Бренд: Insportline Страницы: 96

Бренд: SPORTSTECH Страницы: 74

Бренд: ProForm Страницы: 18

Бренд: ProForm Страницы: 18

Бренд: Hammer Страницы: 27

NordicTrack Commercial X22i

Бренд: ICON Health & Fitness Страницы: 40

Endurance T100A

Бренд: Body Solid Страницы: 44

Бренд: LifeSpan Страницы: 2

Lifestride 5500

Бренд: Life Fitness Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды