Johnson JET 6000 Скачать руководство пользователя страница 17

Страница: 17 / 62

Console Engineering Mode Guide

JET-7000 (Old)

III.

To calibrate the
speed.

IV.

(Old Version)

To choose
metric or
British
mode.

(New Version)

To choose
metric or
British mode.

(Except the ver 0.3)

If the distance between the front bottom edge of the
frame and the floor does not meet the specifications
either at the maximum or minimum incline, you have
to adjust the location of the related limit switch to
calibrate the incline to Spec.

Press Slow, Down, and RESET keys
simultaneously.

While the display reads "CAL-HI", press Up
key. Then the display shows "SLO".

Read the real speed from the window of "TIME". (The
speed value on the "TIME" window is in British
System only)

Using the Fast or Slow keys to adjust the speed of the
treadmill to

0.5mph

(0.8kph).

Then press

START/STOP key

, and the display shows "FAS".

Using the Fast or Slow keys to adjust the speed of the
treadmill to

12.4mph

(20.0kph).

Press to START /STOP key to store.

(OLD):

Hold down

SAFETY

and

POWER

keys, then

remove

SAFETY

key then the display shows "Si" or "bri".

If you want the metric mode, you must remove

POWER

key when the display shows "Si".(the British

mode

"bri") Then the display shows "bye" briefly,

and reset itself.

(NEW):

Hold down

SAFETY

PROGRAM

INTERVAL

and

RESET

keys, then remove

SAFETY

key then the display shows "Si" or "bri".

If you want the metric mode, you must remove

PROGRAM INTERVAL

and

RESET

keys when the

display shows "Si".(the British mode

"bri") Then

the display shows "bye" briefly, and reset itself.

4-1 Revision: 1.0 Date: 2001-06-01

Содержание JET 6000































































Результаты поиска

Содержание JET 6000

Отзывы:

Похожие инструкции для JET 6000

Бренды по названию

Популярные бренды

Johnson JET 6000, Руководство по обслуживанию

Результаты поиска

Содержание JET 6000

Отзывы:

Похожие инструкции для JET 6000

Бренды по названию

Популярные бренды