Johnson JET 6000 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 62

background image

INCLINE MOTOR REPLACEMENT

(JET6000)

Tools required:

ü

Philips screwdriver

ü

Wrench (14mm)

ü

Wrench ( 17mm)

Procedure:

1.

Remove screws from

the front cover by using
the screwdriver to open
the cover.

2.

Disconnect cables from the connectors of the incline
motor and MCB and also disconnect the ground wire.

3.

To prevent the frame from falling down heavily while
removing the incline motor, put a support with
proper height under the front of frame.

4.

Remove the bolts and the nuts from the incline motor by
using the wrenches (14, 17).

5.

Replace the incline motor with a new one.

6.

Reconnect cables and the grounding wire to the
connectors and the frame.

7.

Remove the support under the frame.

8.

Turn on the power and enter the Engineering Mode to
check if the extreme inclines are within the correct
range.

9.

Install the front cover and secure the screws.

7-3 Revision: 1.0 Date: 2001-06-01

«
...
42
43
44
45
46
...
»

Содержание JET 6000































































Отзывы:

Нет отзывов

Похожие инструкции для JET 6000

Pro-Form Trainer 8.0

Бренд: ICON Health & Fitness Страницы: 40

Бренд: Hammer Страницы: 34

Бренд: CYBEX Страницы: 41

Бренд: h/p/cosmos Страницы: 216

Бренд: ICON Страницы: 36

C2270 Treadmill

Бренд: NordicTrack Страницы: 38

Бренд: Quinton Страницы: 82

NEW TFK 135 SLIM

Бренд: Everfit Страницы: 9

Бренд: CAPITAL SPORTS Страницы: 114

StarTrak st3355

Бренд: Orbit Fitness Страницы: 46

Бренд: Sole Fitness Страницы: 37

Бренд: Sole Fitness Страницы: 39

Бренд: Sole Fitness Страницы: 39

Бренд: Weslo Страницы: 18

Бренд: Freemotion Страницы: 32

Бренд: Darwin Fitness Страницы: 64

Бренд: ProForm Страницы: 22

NordicTrack NTL17113.0

Бренд: ICON Health & Fitness Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды