Johnson Controls Intelligent Fire Integrator NION-16C48M Скачать руководство пользователя страница 11

Страница: 11 / 40

NION-16C48M Motherboard Descriptions

Description and Installation

NION-16C48M Installation & Operation Manual - P/N: 53347:Rev: A1 5/5/09

2.2 NION-16C48M Motherboard Descriptions

Figure 2.2 NION-16C48M Board Layout

2.2.1 NION-16C48M Features

The NION-16C48M has the following features:

•

Accepts normally open or normally closed dry contact inputs in any combination.

•

Control outputs are SPDT relays rated at +2.5A @ 30 VDC.

•

Powered from the monitored UL listed panel or a regulated, UL 1481 listed, power limited,
battery backed, +24 VDC power supply.

•

Status, service, input and output LEDs.

•

Inputs can be configured as either two-state unsupervised or four-state supervised with EOL
resistors.

•

Transformer coupled network connection using SMX style transceivers.

•

Software configurable from the Workstation plug-in utility.

•

Transient protection to 2400V on all terminals.

•

Included wall mount enclosure (JNISCAB-3).

Network/Neuron

code (U44)

Application code

(U6)

U44

Configuration

battery backup

CPU

Status LEDs

SMX module

stand-offs

GND +24VDC

TB11 power

connector

SMX network

transceiver header

Reset pin

Comm. LEDs

Binding pin

Input LEDs

Terminal board 1

ribbon cable

connectors

Output relays 1-16

Configuration
jumpers for Inputs
21-24 and 45-48

Configuration
legend for Inputs
21-24 and 45-48

Содержание Intelligent Fire Integrator NION-16C48M









































Результаты поиска

Содержание Intelligent Fire Integrator NION-16C48M

Отзывы:

Похожие инструкции для Intelligent Fire Integrator NION-16C48M

Бренды по названию

Популярные бренды

Johnson Controls Intelligent Fire Integrator NION-16C48M, Руководство по установке и эксплуатации

Результаты поиска

Содержание Intelligent Fire Integrator NION-16C48M

Отзывы:

Похожие инструкции для Intelligent Fire Integrator NION-16C48M

Бренды по названию

Популярные бренды