Johnson & Starley Quantec HR28C ErP Скачать руководство пользователя страница 34

Страница: 34 / 44

www.johnsonandstarley.co.uk

19.

FAULT FINDING FLOWCHARTS

Should a fault occur, the boiler will shut down and these error codes will be displayed.

IGNITION LOCKOUT

OVERHEAT LOCKOUT

FALSE FLAME LOCKOUT

YES

Check siphon and condensate drain pipe

work for blockage and rectify if necessary.

Is boiler working?

Check routing and integrity of internal

boiler wiring.

Check the gas supply

Check wiring connection from gas valve to

PCB for continuity. If the wiring is OK then

replace the PCB.

Replace the pump, the reset the boiler.

Replace the gas valve

Replace board and harness as necessary.

Replace PCB and associated harness as

necessary.

YES

Check the pressure control pipe between fan
and gas valve for continuity, visual condition,

replace as necessary. Is boiler working?

Check the Flow & Return thermistors.

Check resistance using a suitable multi-meter

connection across the thermistor’s terminal

pins

RESET PROCEDURE

To reset the boiler,

press the reset button.

Is the gas pressure available at the boiler

inlet (>18mbar)?

Fill & vent the system & open all isolation

valves, then reset boiler.

Check routing and integrity of the internal boiler

wiring is working OK. Check condition of the Flame

Sensor Electrode and replace if necessary.

Is approx 24 VDC supply available at the

gas valve?

Check that the pump is rotating freely. Is the

differential now below 20°C?

Replace flame detection electrode.

Unplug the gas valve. Is resistance between

outside pins 114

Reset the boiler.

Check board and associated harness for:

continuity and visual condition. Are these

functioning correctly?

Check ignition and associated harness for :

continuity visual condition and position. Are

these functioning correctly?

Replace the Gas Valve.

If the boiler is reset does the boiler ignite for

a short time and then extinguish?

Is the boiler & CH system filled with water

and all isolation & radiator valves open?

Reset the boiler. Is the boiler working?

Check the detection electrode and associated

harness for: continuity, visual condition and

position. Check if the condensate pipe is

blocked. Replace if necessary.

Is the Flow/Return differential across the boiler

in excess of 30°C?

Remove ignition lead and earth tag. Is

there continuity between the terminal pins

connected to the electrode?

FAN FAULT

YES

Replace the Fan.

Rectify wiring & connections

Replace the PCB.

Does the wiring from the fan to the PCB have secure connections at both

ends and has not deteriorated? Does the wiring have continuity?

Is there 230Vac at the Blue Brown connections to the 3 way connection on

the fan

Содержание Quantec HR28C ErP













































Результаты поиска

Содержание Quantec HR28C ErP

Отзывы:

Похожие инструкции для Quantec HR28C ErP

Бренды по названию

Популярные бренды

Johnson & Starley Quantec HR28C ErP, Инструкции по установке, пусконаладке и обслуживанию

Результаты поиска

Содержание Quantec HR28C ErP

Отзывы:

Похожие инструкции для Quantec HR28C ErP

Бренды по названию

Популярные бренды