background image

21

Sales/Spares & Replacement Help Line 01604 762881

12. ELECTRICAL

WARNING: This appliance must be earthed.

12.1 

DROP DOWN CONTROL PANEL

See paragraph 17.5.

12.2 ELECTRICAL 

CONNECTIONS

12.2.1 

A mains supply of 230Vac ~ 50 Hz is required.

12.2.2 

The fuse rating should be 3A. All external controls and wiring must be suitable for mains voltage.

12.2.3 

Wiring external to the boiler MUST be in accordance with the current I.E.E. (BS 7671) Wiring Regulations 
and any local regulations.

12.2.4 

Wiring should be 3 core PVC insulated cable, not less than 0.75mm

2

 (24 x 0.2mm), and to BS 6500. For 

IE reference should be made to the current ETCI rules for electrical installations.

12.2.5  Connection must be made in a way that allows complete isolation of the electrical supply such as a 

double pole switch having a 3mm (

1

/

8

”) contact separation in both poles. The means of isolation must be 

accessible to the user after installation.

12.3 INTERNAL 

WIRING

12.3.1 

The boiler comes pre-fitted with 1.8m of mains cable.

12.3.2 

This must be connected to a permanent live supply and NOT switched by 
thermostats/programmers. 

12.3.3 

The boiler comes pre-fitted with a link wire between the room thermostat/
Timer connections on the terminal strip. This creates a permanent call for 
heat and must be removed when adding a room thermostat/programmer.

12.4 

TO ADD THERMOSTAT/PROGRAMMER

12.4.1   Isolate the mains supply to the boiler.
12.4.2   Remove the front panel. See paragraph 17.5.
12.4.3   Swing the control box down into the servicing position. See Figure 31.
12.4.4   Route incoming cables through the grommets in bottom panel (note, 

grommets are ‘blind’ and will require puncturing) and secure using clamps 
and screws provided in hardware pack.

12.4.5   Connect wires to terminal block.
12.4.6   Swing the control box back up into the operating condition and re-fit the front panel ensuring a good seal 

is made. 

12.5 

THERMOSTATS & TIMER KITS

:

 Telephone Johnson & Starley on 01604 762881 for details. 

12.5.1 

MECHANICAL TIMER (24 HR) KIT:

 

24 hour mechanical CH timer fits into the control box of the boiler. 

This can be fitted in conjunction with a room thermostat.

12.5.2 

ELECTRONIC TIMER (7 DAY) KIT:

 

7 day electronic CH timer fits into the control box of the boiler. 

This can be fitted in conjunction with a room thermostat. Features English language installation help 
messages.

12.5.3 

ROOM THERMOSTAT (NO TIMER)

a.   Remove link wire between Room stat/timer terminals.
b.   Connect room stat across terminals as shown in diagram. See Figure 22.

12.5.4 

ROOM THERMOSTAT with TIMER

a.   Remove link wire between Room stat/timer terminals.
b.   Connect room stat and programmer in series as shown in diagram. See Figure 22.

12.5.5 FROST 

THERMOSTAT

 

If parts of the system are vulnerable to freezing or the programmer is likely to be left off during cold 
weather, a frost stat should be fitted in conjunction with a pipe thermostat.

a.   Position the frost thermostat in a suitable position, i.e. area vulnerable to freezing.
b.   Connect frost stat in series with room stat as shown in diagram. See Figure 22.

12.6 

OPTIONAL SYSTEM CONTROL

 

Open therm protocol controls are available for outside temperature compensation and room temperature sensing 
and can be used to improve the heating system control. They must be connected to the correct terminals as 
described in their own instructions. A room thermostat MUST NOT be used with these controls.

12.7 ELECTRICAL 

TESTING

 

Carry out electrical checks:
• 

Earth continuity and short circuit of cables

• 

Polarity of the mains supply

• 

Insulation resistance to earth

FIGURE 21.

ELECTRICAL CONNECTIONS

/

FIGURE 21

Содержание Quantec HR28C ErP













































Отзывы: